|
2264 | QCAD (main) | Bug Report | Low | Hatching segment selection stops at entity - hatch patt... | Assigned | |
1 |
Task Description
QCAD Professional Windows7 pro WinInstaller Version: 3.26.4.5 (3.26.4.5) Internet: QCAD.org Build Date: Jul 20 2021 Revision: e596276 Qt Version: 5.13.2 Architecture: i386 Compiler: Unknown
In the example given by ‘turtle’ .. why_is_this_not_closed-v2.dxf https://www.qcad.org/rsforum/viewtopic.php?f=32&p=34157#p34153
Selecting hatch boundary segments of the horizontal polyline segment at (1169.933593;274.432562)-(1089.933593;274.432562)
Segment selection stops where the AR-CONC hatch pattern touches the horizontal segment. Such intersections points where already no longer regarded as snappoints. See :
FS#2090 : https://www.qcad.org/bugtracker/index.php?do=details&task_id=2090. Related topic https://www.qcad.org/rsforum/viewtopic.php?&t=7340&p=28414#p28414
Regards, CVH
|
|
2440 | QCAD (main) | Bug Report | Very Low | Hatch from Segments > False positives open loop warning... | Assigned | |
1 |
Task Description
Andrew,
Most probably not related to OS or QCAD version.
When hatching an area with Hatch from Segments (HS) there might be false positive warnings on open loops. It seems that this is related to the orientation of the indicated segments and the order of selection. The real problematic position is not always the first that is reported. Loop count is increased even if it is a single loop.
Included a basic test drawing to replicate these. Further details to replicate the issue are in the file.
Regards, CVH
|
|
839 | QCAD (main) | Feature Request | Low | Grid / Meta Grid info + Drawing Unit Info ... | Assigned | |
1 |
Task Description
At our QCAD Drawing window, below right corner, we have the Info displayed what are the Grid / Meta Grid settings. It would be nice to have additional the Info for the drawing unit ...
|
|
1067 | QCAD (main) | Feature Request | Low | Filling an area with a bitmap | Assigned | |
1 |
Task Description
Being able to fill an area with a bitmap would be a nice addition to the already impressive feature list of QCAD.
|
|
2351 | QCAD (main) | Feature Request | Low | File Thumbnail Preview | Assigned | |
1 |
Task Description
Could we please implement the ability to display file contents in the file explorer. This would make it easier to decide which files to open.
|
|
586 | QCAD (main) | Feature Request | Low | File open dialog with preview | Assigned | |
1 |
Task Description
Since this is not supported by Qt anymore, this would likely have to be implemented from scratch.
|
|
1923 | QCAD (main) | Bug Report | Very Low | Faulty rendering Polylines with Global/Local Widths and... | Assigned | |
1 |
Task Description
Win7pro 32bit Qcad 3.23.0
Andrew, The Arc segments of Polylines with Global or any Local Width render faulty where Global Z or any of the arc’s local Z is not zero.
In the attached drawing setting the Global Z of the inner poly to 5,10,...
The setting of Z to not zero affects the radius of the projected arc and not the bulging of the poly. It also affects the projected widths of the line inversely, but not by changing the widths properties.
Pritty rare combination! True. Qcad is 2D native! True.
Flatten will resolve this.
It is not a purely visual rendering fault, the poly will explode as such.
Maybe similar flaw as with uneven scaling blocks with arcs. https://qcad.org/rsforum/viewtopic.php?f=8&t=5566#p20703
Regards
|
|
2155 | QCAD (main) | Bug Report | Very Low | Faulty rendering Polyline Arcs with Width = 2R | Assigned | |
1 |
Task Description
QCAD Professional Win installer 32bit Version: 3.25.2.4 (3.25.2.4) Internet: QCAD.org Build Date: Nov 18 2020 Revision: 40f4475 Qt Version: 5.13.2 Architecture: i386 Compiler: Unknown
Most likely not related to the QCAD version, rather an old sore.
File included Topic: https://qcad.org/rsforum/viewtopic.php?f=33&t=7889#p30803 Confirmed by ‘cccplex’ Linux ‘Latest Ubuntu’
Polyline arcs with Width = 2R render as circle segments rather than circle sectors. As Non-reversed arcs these don’t explode. As reversed arc these explode to a single arc rather than a circle sector contour.
There is also still the faulty rendering with Z not zero https://qcad.org/bugtracker/index.php?do=details&task_id=1923
Regards, CVH
|
|
951 | QCAD (main) | Feature Request | Low | Extra Option for Block attributes ... | Assigned | |
1 |
Task Description
It would be nice to have the possibility to control the automatic Text orientation in Block attributes. Something what would work like the DIM restriction: I can read the text horizontal and/or from the right side of the drawing sheet.
Right now I have the feeling that the Text orientation is dependent on the tool what I even use. Different tools = different outcomes.
|
|
2446 | QCAD (main) | Feature Request | Low | Extending dimension line beyond extension line when usi... | Assigned | |
1 |
Task Description
I would like the ability to extend dimension lines beyond the extension line when using tick marks. Images are attached and posted here: https://qcad.org/rsforum/viewtopic.php?f=31&t=9785
|
|
1526 | QCAD (main) | Suggestion | Low | Exporting block attributes to CSV | Assigned | |
1 |
Task Description
Two useful commands make it necessary to
1-”delete all the history of the command lines without terminating QCad” ; and
2-”export attributes to the CSV file as exported to the Blocks List”
|
|
1555 | QCAD (main) | Feature Request | Low | Export list of points. | Assigned | |
1 |
Task Description
Hello It would be great when you can add a function to export a selected object as a list of points. Is it possible to add?
Autodes DWG TrueView 2017 has this function and it is very useful. Here you can see a screenshot of this function.
|
|
173 | QCAD (main) | Feature Request | Low | explode text to letters | Assigned | |
1 |
Task Description
implement
|
|
1976 | QCAD (main) | Feature Request | Low | Envelope at offset to a poly tool | Assigned | |
1 |
Task Description
See: https://www.qcad.org/rsforum/viewtopic.php?t=6650
|
|
798 | QCAD (main) | Feature Request | Low | elaborate on purge tool | Assigned | |
1 |
Task Description
Modify the “purge layer” tool to preserve empty layers with a locked status. see: http://www.qcad.org/rsforum/viewtopic.php?f=31&t=2386
|
|
1298 | QCAD (main) | Feature Request | Low | Drawing Preference; File format | Assigned | |
1 |
Task Description
Hi, I get anoyed everytime saving a drawing;
File Format not recommended....... [Yes] ; I know. it's suppose to be in that format!
Saving to file...... [OK] ; I already told you
Black entities ......bla bla [OK] ; I already told you
Custom colors ...... bla bla [OK] ; I already told you
Therefore, Drawing Preferences should start with the file format choice field;
File Format: R.......
Drawing should be opened and saved in that format without any question. Please.
|
|
1702 | QCAD (main) | Feature Request | Low | Draw > Polyline: add boolean operations | Assigned | |
1 |
Task Description
Add intersection, union, difference, XOR operations for closed polylines.
|
|
2160 | QCAD (main) | Bug Report | Low | Draw > Polyline > Relocate Start Point: fails on polyli... | Assigned | |
1 |
Task Description
QCAD Professional Win installer 32bit Version: 3.25.2.7 (3.25.2.7) Internet: QCAD.org Build Date: Dec 16 2020 Revision: e06f230 Qt Version: 5.13.2 Architecture: i386 Compiler: Unknown
Origin: I like to start my CAM paths at low curvature instead starting at high curvature. Ellipses may explode with the startpoint at the tip. (file Y2)
Documented in 3.25.2.4, reproducible under 3.25.2.7
File included with 4 LayerStates - Original Ellipses: Y1 - Exploded to polylines (32 segments): Y2 - Direct after XP, OR performs different on the left top one: Y3 - Faulty solutions by OR: Y4 (= saved state)
The results may differ with the saved explosions.
With the file. Y1 TA XP Relocate startpoint with OR to an existing reference (called ‘End’)
Regards, CVH
|
|
2159 | QCAD (main) | Bug Report | Low | Draw > Polyline > Polyline from Selection: may induce N... | Assigned | |
1 |
Task Description
QCAD Professional Win installer 32 Version: 3.25.2.7 (3.25.2.7) Internet: QCAD.org Build Date: Dec 16 2020 Revision: e06f230 Qt Version: 5.13.2 Architecture: i386 Compiler: Unknown
Discovered in 3.25.2.4, reproducible under 3.25.2.7
Draw any open or closed chain of line entities. Select All. OC to Polyline. Step through vertices.
No example file provided because these NaN values are not saved to a file. More pronounced with lines as with arcs. Less pronounced when recombining after an explosion. Some methods clear these to value = void. Some methods clear these to zero (OR). Can also occur when adding segments to an existing polyline with OC.
Regards, CVH
|
|
2436 | QCAD (main) | Feature Request | Low | Draw > Hatch > Hatch from Segments: mark position of op... | Assigned | |
1 |
Task Description
Case description: “Hatch from Segments” (HS) detects correctly an open loop but fails then to set the circle marker for an easy visuelle identification.
Same scenario tested with “Hatch from Selection” (HA) ... ... everything works like a charm
|
|
2497 | QCAD (main) | Bug Report | Very Low | Draw > Circle > 3 Tangents (CT3) fails in some cases wi... | Assigned | |
1 |
Task Description
Andrew,
See attachment with example:
Solution included on layer ‘Solution’.
Regards, CVH
|
|
625 | QCAD (main) | Feature Request | Low | Distribute block along spline, polyline, ... | Assigned | |
1 |
Task Description
See: http://www.youtube.com/watch?v=27bCgg3zLVA
|
|
756 | QCAD (main) | Bug Report | Low | Display problem in the Text "Character Map" ... | Assigned | |
1 |
Task Description
XP/32
Go to: Text → Special Characters → Others → “Character Map” pops up. Adjust Zoom to 100% = display problem (not enough space for the single character.
|
|
1714 | QCAD (main) | Feature Request | Low | Dimension > Diametric: improve display when label is mo... | Assigned | |
1 |
Task Description
See also: https://www.qcad.org/rsforum/viewtopic.php?f=31&t=5408
|
|
757 | QCAD (main) | Feature Request | Low | Dim: Architectural tick and Leader Arrow size independe... | Assigned | |
1 |
Task Description
Leader Arrow size and the Architectural tick size are controlled by one and the same value.
It would be nice to get the possibility to adjust them independently from each other ...
|
|
2216 | QCAD (main) | Suggestion | Low | DIM modification cause overlapping text | Assigned | |
1 |
Task Description
When I modify partly a DIM with “Stretch” or changing one Extension line position with drag and drop the Value text is updated which is nice working. Unfortunately the previous value stays in place and is overwritten by the actual value. I think for a good readability the previous value should disappear in the moment when the new value is presented.
|
|
2060 | QCAD (main) | Feature Request | Low | Dialog box for Layer Status | Assigned | |
1 |
Task Description
So far, layer status has only been implemented very rudimentarily. I wish something like a dialog box in which you can choose for each layer status, which layers belong to it and which not.
|
|
1503 | QCAD (main) | Feature Request | Low | Detect duplicates within a given selection -new tool re... | Assigned | |
1 |
Task Description
It would be so useful to have an option to be able to detect duplicates within a given selection.
|
|
986 | QCAD (main) | Feature Request | Low | Detect duplicates - only on selected area | Assigned | |
1 |
Task Description
It would be useful to have an additional option to only detect duplicates on user defined selection of drawing. Please see topic: http://www.qcad.org/rsforum/viewtopic.php?f=32&p=9145#p9145
|
|
962 | QCAD (main) | Feature Request | Low | Default save / open directories | Assigned | |
1 |
Task Description
Add the option to use a fixed path for the save to, open and CAM export directories.
(G code files are usually saved in on directory that the Control Program opens them up from so this would save a ton of mouse clicking)
|
|
1833 | QCAD (main) | Feature Request | Low | Deep synchronize attributes feature | Assigned | |
1 |
Task Description
There is the Synchronize attributes feature which works well. But It affects only block references in the active layout(modelspace, block layout). If I want to synchronize attributes of block references in in another blocks, i have to manually go through all blocks and run synchronize attributes feature. That is the reason I would like to modify Synchronize attributes feature to affect all block references in a drawing, or add new Deep synchronize attributes feature.
|
|
1977 | QCAD (main) | Feature Request | Low | Corresponding coordinate format | Assigned | |
1 |
Task Description
Hi,
It would be less confusing to read messages in the command line protocol if it would use the same coordinate separators like the settings below Application Preferences / General / Coordinate Format.
This example shows the “Absolute Cartesian Coordinate” but of course all corresponding format settings should be used within messages.
Absolute Cartesian Coordinate: Setting = semicolon (;) but the message will use division (/).
|
|
2157 | QCAD (main) | Bug Report | Low | Controlpoint Spline exploded to polyline may induce NaN... | Assigned | |
1 |
Task Description
QCAD Professional Win installer 32bit Version: 3.25.2.7 (3.25.2.7) Internet: QCAD.org Build Date: Dec 16 2020 Revision: e06f230 Qt Version: 5.13.2 Architecture: i386 Compiler: Unknown
Documented in 3.25.2.4, reproducible under 3.25.2.7 In the attached file: → Explode the trial cases and locate NaN Widths. → These faulty widths are cleared while saving and reverting. = work around.
Related Post: https://www.qcad.org/rsforum/viewtopic.php?t=7902#p30902 Related Topic: https://www.qcad.org/rsforum/viewtopic.php?t=7901 Related Commit: https://github.com/qcad/qcad/commit/fcd7929bced7ae328029c1aa2ee2aff2745709c6
Arctic_Eddie reports failing CAM offset at exactly these points !!! Reported is a faulty arc with radius of over 360,000mm. - I can not reproduce this under QCAD working further on the Polys with NaNs. - However the direct offset of such controlpoint Splines is erroneous. (see file in post 30902)
Arctic_Eddie reports arc radii of over 10,000mm. - These don’t seem to be faulty. - I agree that BiArc fitting should be bound to a lower and certainly to an upper limit. - That should be huge otherwise faint curvature is represented by many wobbles or too quick by straight lines. (All this, keeping in mind that QCAD doesn’t return the optimum fitted BiArc, see: https://www.qcad.org/rsforum/viewtopic.php?t=4859)
Regards, CVH
|
|
2453 | QCAD (main) | Bug Report | Low | Control point Splines - Issue with Closed & Minimal poi... | Assigned | |
1 |
Task Description
Andrew, For more detailed description please refer to: https://www.qcad.org/rsforum/viewtopic.php?f=33&p=40081#p40081
In the included screen grab below, left is when drawn cubic, closed periodic, from 4 points. Right is when the file is re-loaded.
It is hard to select the incorrect shape when pointing near it ... Probably it is referring to the correct internal shape. After drawing it explodes to a Null length polyline with 2 identical vertices.
I can’t include the error in a file as it reverts on re-load.
The same issue exist for quadratic, closed periodic, from 3 points.
Regards, CVH
|
|
2541 | QCAD (main) | Suggestion | Very Low | Consider the unit "Microinch" to be non-metric | Assigned | |
1 |
Task Description
Andrew,
One Microinch is equivalent to 25.4 nanometers and I don’t consider that to be metric.
RUnit.isMetric(this.getDocument().getUnit()) returns true for RS.Microinch or value 8.
https://github.com/qcad/qcad/blob/master/src/core/RUnit.cpp#L145-L155 Returns false for: RS::Inch ; RS::Foot ; RS::Mile ; RS::Mil ; RS::Yard ... and true for all the rest.
Also see last note in: https://www.qcad.org/rsforum/viewtopic.php?f=31&t=9506&p=38295
Not to be confused with RDocument::isMetric() because that returns the measurement system unless that is RS::UnknownMeasurement what is rather impossible with drawings created by QCAD.
Regards, CVH
|
|
1705 | QCAD (main) | Feature Request | Low | Connect certain actions and layers | Assigned | |
1 |
Task Description
When dimensioning my drawings I always want the dimensions to be on the dimensions layer. When adding text I want the text to be on the text layer. When drawing an infinite line it is always a construction line, therefore I want it to be on the construction line layer. When drawing a line segment it almost always is on my outline layer.
So I propose a new option to bind certain actions to certain layers. Whenever those actions are selected the layer should automatically be switched.
I can imagine this being implemented in the General→Tool Settings menu, where the short cuts are defined.
|
|
670 | QCAD (main) | Feature Request | Low | Configurable rendering options for stacked text | Assigned | |
1 |
Task Description
Customer wishes that stacked text used as subscript is rendered differently (i.e. increased text size, lower position for subscript). This may also apply to superscripts.
|
|
684 | QCAD (main) | Feature Request | Low | Configurable behavior for using box selection with Shif... | Assigned | |
1 |
Task Description
See also: http://www.qcad.org/rsforum/viewtopic.php?f=32&t=2180
|
|
2167 | QCAD/CAM | Bug Report | Low | Comma format decimal separator fails ZSafety CAM config... | Assigned | |
1 |
Task Description
QCAD/CAM Trial package Win installer 32 bit Version: 3.25.2.0 (3.25.2) Internet: QCAD.org Build Date: Sep 4 2020 Revision: 4a61501 Qt Version: 5.13.2 Architecture: i386 Compiler: Unknown
Local decimal separator is ‘,’ (comma) In CAM configuration .. Z Levels .. Safety level
Using nn,nnn the output is Nxx G0 Znn Using nn.nnn the output is Nxx G0 Znn.nnn
Drop down boxes are all in dot format. Didn’t try anything else yet
Regards, CVH
|
|
1452 | QCAD (main) | Feature Request | Low | Colour opacity option | Assigned | |
1 |
Task Description
Not sure how difficult this would be to implement but just wondered if it is possible to have an option in QCAD to change the opacity of a colour ?
related to topic: http://www.qcad.org/rsforum/viewtopic.php?f=83&p=15715&sid=45f0f0679e8257f3cf98f91e4f0c4577#p15715
|
|
609 | QCAD (main) | Feature Request | Low | Clean up tool | Assigned | |
1 |
Task Description
To have a ‘clean up ' tool to:
- eradicate duplicate lines - eradicate stray points - remove empty layers - remove unused blocks
Perhaps with an initial dialog which allows the user to choose what they want to clean up.
|
|
2140 | QCAD (main) | Suggestion | Low | Changing navigation mode for mouse wheel doesn't change... | Assigned | |
1 |
Task Description
Looks like error, but may be that’s feature request.
CAD software uses typical navigation behavior as: Wheel = Zoom; Ctrl+Wheel = Scroll up/down; Shift+Wheel = Scroll left/right.
Any other software like browsers, office software (openoffice writer, ms excel and so on), 2d paint software like GIMP (Photoshop and so on) uses other behavior: Wheel = Scroll up/down; Ctrl+Wheel = Zoom; Shift+Wheel = Scroll left/right.
Users, that intensively use CAD and other software simultaneously prefer to make same behavior in their applications switching CAD scroll to plain mouse wheel.
QCAD’s “Application Preferences”: “Graphics View: Navigation”: “Mouse wheel/ two finger swipe”: “Scroll” allow user to assign scroll up/down to wheel mouse instead of Zoom. But there is mistake Ctrl+Wheel didn’t change to Zoom. Ctrl+Wheel continues to scroll up/down, as the wheel. Wheel = Scroll up/down; Ctrl+Wheel = Scroll up/down; Shift+Wheel = Scroll left/right. No zoom!
Draw manipulation at this mode like a hell: you need to use wheel in conjunction with Ctrl/Shift to point draw in desired position, than move your hand to +(-) for make desired zoom.
|
|
1282 | QCAD (main) | Feature Request | Low | Changeable color of the selection bar in layer list. | Assigned | |
1 |
Task Description
Changeable color of the selection bar in the layer list. Now the color of the bar is darkblue and the underlaid icons are black and are not readable.
|
|
525 | QCAD (main) | Feature Request | Low | change the printed symbol of points | Assigned | |
1 |
Task Description
Hi,
in QCAD3 RC2 points were printed as crosses, in QCAD3 RC4 they are printed as (very little) points. I think this isn’t a bug but a feature.
It would be nice if one could change this behaviour / select the symbol of points.
Best regards - Stefan
This is a double post of http://www.ribbonsoft.com/rsforum/viewtopic.php?p=5870#5870 as suggested there.
|
|
1810 | QCAD (main) | Feature Request | Low | Change icons from black on white to white on black depe... | Assigned | |
1 |
Task Description
Automatic change of icons in the Library Browser from black on white to white on black or vice versa depending on the background (white or black; light or dark) in QCAD main window. See also https://www.qcad.org/rsforum/viewtopic.php?f=31&p=21970#p21970
|
|
1469 | QCAD (main) | Suggestion | Low | Cartouche automatique | Assigned | |
1 |
Task Description
Would not it be possible to create a kind of template for printing? We draw our room without cartridge. The cartridge will automatically appear when printed. The scaling could be automatic so that it goes in the A4 and therefore also will post the scale automatically. The name of the play could be the file name, date last saved after it the rest of the information that would be to add somehow (material index, designer, ...).
Original suggestion:
Bonjour,
Ne serait il pas possible de créer une sorte de template lors de l’impression ? On dessine notre pièce sans cartouche. Le cartouche s’affiche automatiquement lors de son impression. La mise à l’échelle pourrais être automatique pour que ca rentre dans le A4 et donc l’échelle s’afficherai aussi en automatique. Le nom de la pièce pourrais être le nom du fichier, la date du dernier enregistrement après c’est le reste des infos qui serait à ajouter je ne sais comment (matière, indice, dessinateur, ...).
|
|
1940 | QCAD/CAM | Feature Request | Low | CAM > CAM Configuration: Add program description | Assigned | |
1 |
Task Description
Add a program description to the CAM configuration dialog and export to postprocessors as variable.
See also: https://www.qcad.org/rsforum/posting.php?mode=quote&f=32&p=24649
|
|
2138 | QCAD (main) | Suggestion | Very Low | Block zoomstate supersedes Model_Space after Undo of BC | Assigned | |
1 |
Task Description
Summary: Block zoomstate supersedes Model_Space after Undo of BC
QCAD Professional Version: 3.25.2.1 (3.25.2.1) Internet: QCAD.org Build Date: Oct 15 2020 Revision: 2895712 Qt Version: 5.13.2 Architecture: i386 Compiler: Unknown «< (Win installer 32 bit)
With the file provided: ZW to see the top green ‘revision cloud’ up close QQ Box select around the cloud »> 2 entities in selection BC, select origin somewhere inside the selection, accept proposed naming »> ‘Block 1’ is created from the selection TN BD, select the newly created Block Reference »> Auto zoom of ‘Block 1’ (Intended behavior) OO »> Returns to Model_Space with the zoomstate of the removed Block »> Halfway down the drawing »> The former zoomstate of the Model_Space is lost
Intended behavior is that the zoomstate of Model_Space and Blocks don’t mix See: https://www.qcad.org/rsforum/viewtopic.php?f=31&t=7797&p=30371#p30378
This proves they do, even if the block doesn’t exists anymore.
Regards, CVH
PS: 3th trial to enter a suggestion ...
|
|
2547 | QCAD (main) | Bug Report | Very Low | Block > Purge Unused Blocks > Removes _DatumFilled bloc... | Assigned | |
1 |
Task Description
Andrew,
The _DatumFilled Block used by Datum entities (DT) is considered as not used and is purged by Purge Unused Blocks (BP). There is no block association for these special types of arrowheads in QCAD.
After purging the Datums are not immediately updated but the special arrowheads will eventually disappear. Adding new Datums will not fix that.
Not problematic because the _DatumFilled Block is re-created on save/reload when Datum entities exists. Datums are updated.
Probably not OS or version related. Related forum topic: https://www.qcad.org/rsforum/viewtopic.php?f=89&t=10694
Best solution would be to support different types of arrowheads and all related: https://qcad.org/bugtracker/index.php?do=details&task_id=695 https://qcad.org/bugtracker/index.php?do=details&task_id=757 https://qcad.org/bugtracker/index.php?do=details&task_id=1157
Regards, CVH
|
|
1169 | QCAD (main) | Feature Request | Low | Bitmap clipping | Assigned | |
1 |
Task Description
Clipping bitmaps to only show a part of the image.
See: http://www.qcad.org/rsforum/viewtopic.php?f=32&t=3263
|