QCAD Bugtracker

QCAD - 2D CAD System.

Click here for a documentation of the DokuWiki formatting syntax that can be used in reports

Please search for existing tasks (also closed ones) before opening a new task.

Please make sure that you are using the latest Version of QCAD before posting a bug (menu Help > Check for Updates)

IDCategoryTask TypeSeveritySummaryStatus  ascProgress
1760QCAD (main)Bug ReportVery LowSelf-crossing polylines can't be cut twice at segment c...Assigned
0%
Task Description

Re-entering dividing problem from  FS#1757 

Divide the poly selecting near segment 1 at the segment crossing.
> A new node is inserted on the crossing and made start and end node.
Divide the poly again selecting near segment 2 at the segment crossing.
> no division appears to be done.

One can’t divide the second segment at the crossing

Presumed intended behaviour like  FS#1750 

Regards

1762QCAD (main)Bug ReportVery LowModify // .... selection of entities on locked layer al...Assigned
0%
Task Description

Not served with the degration to ‘Suggestion’ FS#1759.
Demanded closing FS#1759 & re-entered

Locking entities (by layer) to avoid selection,eg. nearby,very close by or on the same spot, does not have the intended influence.

Asumed wrong:
- Modify DI
- Modify B2
- Modify D3
- Modify MT
These 4 need a single entity to be selected and selection of a locked entity is allowed.(=questionable)
The action will allways leed to ‘not allowed’.(=correct)

Questionable:
- Modify RM
- Modify CH
- Modify RN
These 3 need a pair of entities.
RM: Selection of a locked limiting entity is allowed (=questionable), enity to trim not.(=correct)
The action will trim unlocked entities to the locked limiter.(=questionable)
CH & RN: Selection of a pair of entities is allowed.(=questionable)
Trimming if ‘trim’ is on will not occur because locked and leeds to ‘not allowed’.(=correct)
The creation of the bevel or rounding on an active locked layer will not occur because locked and leeds to ‘not allowed’.(=correct)
The creation, except for polyline segments (because locked themself), on an active unlocked layer will be done.(=correct)

Less severe but still questionable: (because these don’t necerally act on the locked entities themselves)
- Modify OF
- Modify OH
- Modify SS
OF: Selection of a locked base entity is allowed.(=questionable)
The preview is casted only if the active layer is unlocked.(=correct)
The creation is only done on an active unlocked layer.(=correct)
OH: Selection of a locked base entity is allowed.(=questionable)
Selection of point references from entities on locked layers is allowed.(=questionable)
The preview is casted only if the active layer is unlocked.(=correct)
The creation is only done on an active unlocked layer.(=correct)
SS: Selection of point references from entities on locked layers is allowed.(=questionable)
Strechting is only done for unlocked entities. (=correct)

1765QCAD (main)Bug ReportVery LowErrors with polyline offsetAssigned
0%
1 Task Description

Win 7 32 bit QCAD 3.20.1

Ofsset of a base-line with arcs results in massive ammount of errors.
Most of them occur as a cluster of very tiny segments and are part of the offset. (zoom far in at the red circles)
Mostly they occur where the offsetted arcs should merely be trimmend pairwise.
Some occur as detached entities or as detached strings of entities very near the offset (strings not documented).
Spooks occur at opposite site when base-line is not closed.
360° curls can occur with R = Offset.
Null-entities may occur (not documented, hard to find and not able to copy).

The base-line is checked and sound and has mixed tangentially or not tangentially connected arcs.
Offsetting the mother base-line of the base in the file has similar effect but not all and/or different ones.
Also encountered with offseting polys from fonts.
Used to define pocket paths for CNC.
Detected because the CNC driver will not accept Self-crossers, Null-entities or open ends depending on the settings.

Work arround is to explode and select small entities but this does not solves the issues.
1) Choosing the tolerance large enough will detect small segments that should stay.
2) Recombining will generate new ones at the place where the main segments remain crossed.
Cleaning up the paths is a daunting process with some thousand segments for several offsets.

I assume this has an infuence on the CAM part of QCAD too unless the offset method is different.

1285QCAD (main)Feature RequestLowProperty PainterResearching
0%
2 Task Description

Easy transfer of properties from one entity to others

1394QCAD (main)Feature RequestLowArc length dimensionRequires Testing
90%
1 Task Description

Support arc length dimenions (undocumented DXF entity ‘ARC_DIMENSION’).
Create arc length dimensions with parallel extension lines for angle < 90, orthogonal extension lines otherwise.
Display arc symbol beside or on top of label text.

259QCAD (main)Feature RequestMediumChain dimensionsLikely to be implemented
0%
11 Task Description

Chain dimensions

260QCAD (main)Feature RequestMediumReference dimensioningLikely to be implemented
0%
9 Task Description

Reference dimensioning (baseline dimensioning)

Create multiple dimensions using the same base line.

693QCAD (main)Feature RequestMediumSupport for external references (XREF)Likely to be implemented
0%
13 Task Description

Support for external references (XREF)

694QCAD (main)Feature RequestMediumUser coordinate systems (UCS)Likely to be implemented
0%
5 Task Description

UCS support.

1127QCAD (main)Feature RequestLowLeaders: spline shapedLikely to be implemented
0%
1 Task Description

Add support for spline shaped leaders

1224QCAD (main)Feature RequestLowRevision cloudsLikely to be implemented
0%
2 Task Description

Add support to draw revision clouds or convert polylines, ellipses, circles to revision clouds.

Showing tasks 351 - 361 of 361 Page 8 of 8<<First - 4 - 5 - 6 - 7 - 8

Available keyboard shortcuts

Tasklist

Task Details

Task Editing