|
721 | QCAD (main) | Bug Report | Low | Vertical dimensions imported as horizontal dimensions | Assigned | |
|
Task Description
Vertical dimensions created with 3rd party applications are sometimes imported as horizontal dimensions with length 0. Changing the angle in the property editor fixes the problem. Problem occurs in QCAD 2.2 and QCAD 3.0.
|
|
2289 | QCAD (main) | Bug Report | Low | Vertical Line Tool stops accepting input | Assigned | |
|
Task Description
When using the vertical line tool, you can enter a length value in the options toolbar, then place the line. If you want to change the length, you just need to enter a new value and the length field will update. However, there seem to be cases where after 10-20 entries, the focus goes off the length field in the options toolbar, requiring the user to bring focus back to continue. I could not seem to duplicate this behavior with the horizontal line tool.
|
|
2189 | QCAD (main) | Feature Request | Low | Vertically and/or diagonally stacked fractions option. | Assigned | |
2 |
Task Description
The option for vertically and diagonally stacked fractions would be helpful for both the text creation tool and as the output of dimensions.
|
|
705 | QCAD (main) | Bug Report | Low | Verwaltung Library Resourcen und Favoriten .... | Assigned | |
|
Task Description
Ob dies ein Feature Request oder ein Bugreport ist weiß ich nicht ....
Hier meine Gedanken ....
In den Application Preferences kann ich mehrere Library Sources vorgeben. Ich habe eine auf dem HD und eine auf einen USB angegeben.
Wenn ich nun QCad auf der HD ausführe habe ich beide Ressourcen zur Verfügung. Schön! Natürlich habe ich auch im Library Browser meine Favoriten von beiden Ressourcen angegeben.
Wenn ich nun aber den USB entferne zeigt mir der Library Browser immer noch beide Resorcen als Name an - schalte ich nun um auf die USB Resource bekomme ich keinerlei Hinweis das diese momentan nicht zur Verfügung steht. Es passiert einfach NIX Es wäre schön wenn ich hier eine “Nicht verfügbar” Meldung bekommen würde.
Wenn ich nun meine Trotteligkeit bemerke und den USB wieder einstecke habe ich logischerweise wieder meine Library zur Verfügung ..... nur die auf den USB Stick verweisenden Favoriten sind auf Nimmerwiedersehen verschwunden. Die auf dem HD bleiben erhalten!
OK - um es ganz rund zu machen ein anderes Szenarios in “Steno”: QCad Start vom USB - > Library Favoriten anlegen auf USB Library - > QCad schließen - > USB entfernen → QCad auf HD starten - > Library Favoriten auf USB sind verschwunden - > QCad HD schließen - > USB einstecken und QCad von USB starten = Favoriten auf USB bleiben verloren!
Wäre es hier nicht möglich die Favoriten Information dem USB mit auf dem Weg zu geben? Wenn ich eine Favoriten Auswahl auf dem USB nicht kontrollieren kann macht diese Möglichkeit kaum Sinn.
|
|
1133 | QCAD (main) | Feature Request | Low | View > Add View: save layer state | Assigned | |
1 |
Task Description
Save layer state (visibility) with each added view object (optional?).
|
|
1596 | QCAD (main) | Feature Request | Low | View > Selection Filter: add filter for custom properti... | Assigned | |
3 |
Task Description
See also: https://qcad.org/rsforum/viewtopic.php?f=32&t=4840
|
|
1541 | QCAD (main) | Feature Request | Low | View > Zoom > Zoom In/Out: Make zoom factor configurabl... | Assigned | |
1 |
Task Description
See also: https://www.qcad.org/rsforum/viewtopic.php?f=32&t=4729
|
|
1915 | QCAD (main) | Suggestion | Low | Viewport does not rotate view-port when changed in pape... | Assigned | |
|
Task Description
To reproduce
1. Select a new view-port in model-space 2. Select the appropriate paper-space 3. When the paper space opens change the angle of the viewport.
Actual
The object in the viewport changes but the viewport itself remains unchanged
Expected
That both the view-port and the object changes angle as the angle is updated
Motivation
If you abort the placement (but keep the angle) and go back to model-space and then redo the operation the view-port is rotated along the angle. It seems that the viewport only picks up the initial angle once the paper-space is open and ignores any changes thereafter
Workaround
1. Select the view-port per normal in model-space 2. Open the paper-space and set the wanted angle but do not place the view-port in paper space 3. Abort the placement on paper-space and redo the whole operation
Once the paper space is opened again the view-port will have the chosen angle
|
|
2308 | QCAD (main) | Feature Request | Low | Viewport Scale Field | Assigned | |
|
Task Description
It would be helpful if the scale field that appears while placing a viewport would also re-appear when the viewport is selected after it’s already been placed in the layout. It would also be helpful if the pre-populated values in the dropdown matched those in the global layout scale field.
|
|
1999 | QCAD (main) | Feature Request | Low | Viewport: Add additional properties for controlling dim... | Assigned | |
3 |
Task Description
When working with multiple Viewports with different scale it could be very useful to have extra properties controlling how dimensions are rendered in the viewport:
1) E.g an extra “Dimension Scale” under “Scale” in the Viewport selection’s ‘Specific Properties’ section, could allow having the same size when printed. This Dimension Scale would be multiplied on top of the Scale value, but only for Dimensions rendering.
2) Toggle button for hiding any dimensions in the Viewport. Maybe this should be controlled by being able to specify a Layer that should be hidden in this Viewport only, then I could select my Dimensions layer here.
The Viewport properties: https://i.imgur.com/s07JtaB.png
|
|
637 | QCAD (main) | Feature Request | Low | Viewports / View List | Assigned | |
|
Task Description
1. The Scrollbars for each window in the Viewports has the same size like the normal used scrollbars for windows. If you are working on a normal size Monitor it “steals” a lot of “working space”. Is there any possibility to make the scrollbars smaller or just a line to separate the windows so that I have to navigate with Keyboard and mouse?
2. I thing the Viewports and the View List belongs together - is it possible to get a button in the “View List / Tool Bar” to choose a Viewport style instead of “walking” the long way over the “Drawing preferences” Menu?
See also: http://www.ribbonsoft.com/rsforum/viewtopic.php?f=47&t=2071
|
|
1754 | QCAD (main) | Suggestion | Low | When Selecting multiple blocks that contain the same at... | Assigned | |
|
Task Description
When selecting multiple blocks that contain the same attribute names, attribute properties appear with the values of the last selected block instead of “various”. I do not know if this is a “bug” or developer option, but “various” would be better in my opinion.
|
|
1863 | ECMAScript | Feature Request | Low | WidgetFactory.saveState: save state of checkable QGroup... | Assigned | |
|
Task Description
QGroupBox widgets with <property name=”checkable”> are not saved in Qcad3.conf
|
|
2552 | QCAD (main) | Bug Report | Low | Windows shortcut Alt + Underlined Key fails partly in m... | Assigned | |
|
Task Description
Reason: Same underlined keys are used for different menus
Select and Snap = S, Dimension and Info = I, Modify and Misc = M,
|
|
1506 | dxflib | Feature Request | Low | writeVPort parameters | Assigned | |
|
Task Description
Add parameters to the function DL_Dxf::writeVPort. This way users will be able to specify the desired viewport.
Is the github the official repository? Are pull requests sent there accepted?
|
|
1811 | QCAD (main) | Feature Request | Low | Zoom 1:1 | Assigned | |
2 |
Task Description
It would be nice to be able to adjust the zoom factor so that the scale on the screen matches a ruler which I lay on the screen.
Thanks!
|
|
2284 | QCAD (main) | Bug Report | Low | Zooming in & out causes grid/snap scale value change in... | Assigned | |
1 |
Task Description
I have set the grid/snap value to X=.0625 Y=.0625 on all 4 viewports. When zooming in and out the grid/snap scale changes from .0625 to 3.90625. at this point the grid/snap points differ, This causes a variation in the grid/snap reference points lending to drawing errors.
example When I use the grid settings defaults .01, when zooming in and out, the grid/snap scaling doesn’t seem to have this issue. Other values do, See below.
set value first zoom second zoom next zoom
point point point ...
0.01 0.1 1.0 10.0 ... 0.02 0.04 0.4 4.0 ... 0.04 0.16 1.6 16.0 ... 0.05 0.25 2.5 25.0 ... 0.0625 0.390625 3.90625 39.0625 ... 0.0254 0.64516 6.4516 64.516 ...
Why is there a squaring of the original set value? Which then becomes a new zoomed grid/snap value?
QCAD Professional Version: 3.26.4.0 (3.26.4) Internet: QCAD.org Build Date: Jun 3 2021 Revision: 0bb4334 Qt Version: 5.13.2 Architecture: i386 Compiler: Unknown
|
|
2088 | QCAD (main) | Bug Report | Very Low | column headers of the "General: tool settings " resize... | Assigned | |
|
Task Description
Open QCAD and the application preferences. In the section “General: tool settings " you can resize the columns: Menu, Shortcuts etc. The problem is that it is not intuitive. The first divider is not selectable and the second moves the first, only backwards.
|
|
1626 | QCAD (main) | Feature Request | Very Low | 'Clip to Circle' tool | Assigned | |
1 |
Task Description
Hi Andrew,
Would it be possible to have a clip to circle tool also please?
Regards
Clive
|
|
2539 | QCAD (main) | Bug Report | Very Low | (Relative) Polar feet + surveyor notation fails. | Assigned | |
1 |
Task Description
Andrew,
A user essentially pointed out to an ACAD textbook example. https://qcad.org/bugtracker/index.php?do=details&task_id=2533 Step 3 of: https://autodesk.blogs.com/between_the_lines/2012/07/drawing-with-surveyors-units-in-autocad.html
Please refer to this topic: https://www.qcad.org/rsforum/viewtopic.php?f=33&t=10652
Regards, CVH
|
|
2107 | QCAD (main) | Feature Request | Very Low | Add a button to the tool bar to allow for a quick backg... | Assigned | |
1 |
Task Description
I find myself with reasonable regularity needing to change the background color between black and white. It would be much more efficient to have a toggle button on the ribbon to make this sort of instant (kind of like the “screen based line types” button works but make it for background color and just between black and white or let people define their dark and light themes and toggle the background between the two.
|
|
1649 | QCAD (main) | Feature Request | Very Low | Add configuarable format options for saving blocks to l... | Assigned | |
|
Task Description
Add configuarable format options in application preferences for saving blocks to library to either dxf or dwg.
|
|
1922 | dwg2bmp | Feature Request | Very Low | Add error message when requesting raster for a non-exis... | Assigned | |
|
Task Description
It would be nice if QCAD spit some kind of warning message when trying to render a layer with a name that doesn’t exist (and perhaps render nothing), rather than silently rendering an empty image. :D
See https://qcad.org/rsforum/viewtopic.php?f=33&t=6453
|
|
2501 | QCAD (main) | Feature Request | Very Low | Add spelling checker / spell checker for all text boxes | Assigned | |
1 |
Task Description
Suggestion to add spelling checker / spell checker for all text boxes
|
|
752 | QCAD (main) | Feature Request | Very Low | Add support for the 3dConnexion Space Navigator (Pan an... | Assigned | |
4 |
Task Description
The 3dConnexion Space Navigator would be wonderful as a pan and zoom control. I find it extremely useful in SketchUp and when I switch from that to QCAD am always disappointed to find it doesn’t work.
3dconnexion DOT com/buy/shop.html?3dxcp=GA_GA_search_google_US_Brand
While full support for the buttons and such would be nice, just the ability to map the axis to pan and zoom would be wonderful.
|
|
991 | QCAD (main) | Feature Request | Very Low | Add warning when overwriting custom property | Assigned | |
1 |
Task Description
Property Editor - Geometry - Custom - Add Custom Property
If I use an identical Name accidentally again in the Custom Property dialog - it will overwrite the first value with the same name without any warnings.
|
|
2147 | QCAD (main) | Suggestion | Very Low | Allow breaking up self-intersecting a 2e time (at endpo... | Assigned | |
1 |
Task Description
QCAD Professional win installer 32bit Version: 3.25.2.4 (3.25.2.4) Internet: QCAD.org Build Date: Nov 18 2020 Revision: 40f4475 Qt Version:5.13.2 Architecture: i386 Compiler: Unknown
Continued from https://qcad.org/bugtracker/index.php?do=details&task_id=1757 Splitting the old report up ... Same file. In the left example one can cut (DI) once. Cutting the second segment results in NO cut.
Regards CVH
|
|
2149 | QCAD (main) | Suggestion | Very Low | Allow undo after auto trim self-intersecting with AX in... | Assigned | |
1 |
Task Description
QCAD Professional win installer 32bit Version: 3.25.2.4 (3.25.2.4) Internet: QCAD.org Build Date: Nov 18 2020 Revision: 40f4475 Qt Version:5.13.2 Architecture: i386 Compiler: Unknown
Continued from https://qcad.org/bugtracker/index.php?do=details&task_id=1757 Splitting the old report up ... Same file. In the left example one can auto trim (AX): - The lower loop. - The top loop. Bug? The action on the top loop can’t be undone.
Regards CVH
|
|
2148 | QCAD (main) | Suggestion | Very Low | Allow undo after breaking up self-intersecting with D2 ... | Assigned | |
1 |
Task Description
QCAD Professional win installer 32bit Version: 3.25.2.4 (3.25.2.4) Internet: QCAD.org Build Date: Nov 18 2020 Revision: 40f4475 Qt Version:5.13.2 Architecture: i386 Compiler: Unknown
Continued from https://qcad.org/bugtracker/index.php?do=details&task_id=1757 Splitting the old report up ... Same file. In the left example one can break out segment (D2): - removing one of the loops with the ‘remove’ option. - leaving both without the ‘remove’ option. Bug? Without the ‘remove’ option it can’t be undone.
Regards CVH
|
|
2181 | QCAD (main) | Suggestion | Very Low | Apply more distinguishable Enabled and Disabled state i... | Assigned | |
1 |
Task Description
QCAD Professional Win7 WinInstaller 32bit Version: 3.25.2.7 (3.25.2.7) Internet: QCAD.org Build Date: Dec 16 2020 Revision: e06f230 Qt Version: 5.13.2 Architecture: i386 Compiler: Unknown
Related forum Topic: https://qcad.org/rsforum/viewtopic.php?t=8015
CVH
|
|
2461 | dxflib | Bug Report | Very Low | ASCII Control characters not handled correctly in Commu... | Assigned | |
|
Task Description
I see the following problem: When I open a particular DXF file in the Professional Trial version 3.27.9.0 on macOS, “^I” in text fields is expanded to whitespace. When I open the same DXF file in the Community Edition 3.27.9.0 on NetBSD/x86_64 (installed from pkgsrc), “^I” in text fields is visible as “^I”.
|
|
2547 | QCAD (main) | Bug Report | Very Low | Block > Purge Unused Blocks > Removes _DatumFilled bloc... | Assigned | |
1 |
Task Description
Andrew,
The _DatumFilled Block used by Datum entities (DT) is considered as not used and is purged by Purge Unused Blocks (BP). There is no block association for these special types of arrowheads in QCAD.
After purging the Datums are not immediately updated but the special arrowheads will eventually disappear. Adding new Datums will not fix that.
Not problematic because the _DatumFilled Block is re-created on save/reload when Datum entities exists. Datums are updated.
Probably not OS or version related. Related forum topic: https://www.qcad.org/rsforum/viewtopic.php?f=89&t=10694
Best solution would be to support different types of arrowheads and all related: https://qcad.org/bugtracker/index.php?do=details&task_id=695 https://qcad.org/bugtracker/index.php?do=details&task_id=757 https://qcad.org/bugtracker/index.php?do=details&task_id=1157
Regards, CVH
|
|
2138 | QCAD (main) | Suggestion | Very Low | Block zoomstate supersedes Model_Space after Undo of BC | Assigned | |
1 |
Task Description
Summary: Block zoomstate supersedes Model_Space after Undo of BC
QCAD Professional Version: 3.25.2.1 (3.25.2.1) Internet: QCAD.org Build Date: Oct 15 2020 Revision: 2895712 Qt Version: 5.13.2 Architecture: i386 Compiler: Unknown «< (Win installer 32 bit)
With the file provided: ZW to see the top green ‘revision cloud’ up close QQ Box select around the cloud »> 2 entities in selection BC, select origin somewhere inside the selection, accept proposed naming »> ‘Block 1’ is created from the selection TN BD, select the newly created Block Reference »> Auto zoom of ‘Block 1’ (Intended behavior) OO »> Returns to Model_Space with the zoomstate of the removed Block »> Halfway down the drawing »> The former zoomstate of the Model_Space is lost
Intended behavior is that the zoomstate of Model_Space and Blocks don’t mix See: https://www.qcad.org/rsforum/viewtopic.php?f=31&t=7797&p=30371#p30378
This proves they do, even if the block doesn’t exists anymore.
Regards, CVH
PS: 3th trial to enter a suggestion ...
|
|
2021 | QCAD (main) | Performance Issue | Very Low | Cannot work with big dwg files | Assigned | |
|
Task Description
Openning a big file or doing any action in it, takes minutes to load. Even dragging the scrollbar slightly left or right, takes mintues to redraw the canvas again, which makes QCAD un-usable for professional use. Is there a way to make QCAD usable, after loading completed: - Like suppressing edit until user says so, - or taking snapshots of rendered canvases to another file and use it, as windows uses thumb.db ( for negative latency :P )
PS: I wish I could help a bit, but my hand are tied. I am just a java freak, I am opt to any idea of porting it to java, if she is still alive.
Tuğalsan Karabacak EEE, MSc Mobile Comp & App, IWE
|
|
2541 | QCAD (main) | Suggestion | Very Low | Consider the unit "Microinch" to be non-metric | Assigned | |
1 |
Task Description
Andrew,
One Microinch is equivalent to 25.4 nanometers and I don’t consider that to be metric.
RUnit.isMetric(this.getDocument().getUnit()) returns true for RS.Microinch or value 8.
https://github.com/qcad/qcad/blob/master/src/core/RUnit.cpp#L145-L155 Returns false for: RS::Inch ; RS::Foot ; RS::Mile ; RS::Mil ; RS::Yard ... and true for all the rest.
Also see last note in: https://www.qcad.org/rsforum/viewtopic.php?f=31&t=9506&p=38295
Not to be confused with RDocument::isMetric() because that returns the measurement system unless that is RS::UnknownMeasurement what is rather impossible with drawings created by QCAD.
Regards, CVH
|
|
2497 | QCAD (main) | Bug Report | Very Low | Draw > Circle > 3 Tangents (CT3) fails in some cases wi... | Assigned | |
1 |
Task Description
Andrew,
See attachment with example:
Solution included on layer ‘Solution’.
Regards, CVH
|
|
2328 | QCAD (main) | Bug Report | Very Low | drop down, using keyboard | Assigned | |
|
Task Description
Minor issue! When using keyboard to initiate the dropdown menus. I noticed the ALT “D” does not cycle through the headings Draw & Dimension in the same way. ALT “M” cycles though Modify & Misc or ALT “S” cycles though Select & Snap. User Name: StanTibbs E-mail: [email protected]
|
|
1920 | QCAD (main) | Feature Request | Very Low | Edit > Application Preferences: Add preference to disab... | Assigned | |
|
Task Description
See also: https://www.qcad.org/rsforum/viewtopic.php?f=89&t=6447
|
|
2287 | QCAD (main) | Feature Request | Very Low | Evaluate draw order for preference "Prevent white-on-wh... | Assigned | |
|
Task Description
The Application Preference setting “Graphics View - Appearance - Prevent white-on-white/black-on-black display” seems to be a global setting that doesn’t take the draw order into account. For example: With the setting enabled, it prevents creating a white hatch of a higher draw order on top of a larger, colored hatch with lower draw order (background). The preference does not seem to evaluate if the object is truly drawn as “white-on-white”.
With the preference enabled, setting the object color as “white” will set the “white” color label, but the object color actually stays black. Its hard to determine why it happens in that case.
Is it possible to let the global preference setting be applied to objects after evaluation of the draw order, and determine if the object actually is a true case of white-on-white?
My workaround: Disable the preference setting (I think it is default = on), and only enable it for ad-hoc checks of hidden and overlooked objects.
|
|
2155 | QCAD (main) | Bug Report | Very Low | Faulty rendering Polyline Arcs with Width = 2R | Assigned | |
1 |
Task Description
QCAD Professional Win installer 32bit Version: 3.25.2.4 (3.25.2.4) Internet: QCAD.org Build Date: Nov 18 2020 Revision: 40f4475 Qt Version: 5.13.2 Architecture: i386 Compiler: Unknown
Most likely not related to the QCAD version, rather an old sore.
File included Topic: https://qcad.org/rsforum/viewtopic.php?f=33&t=7889#p30803 Confirmed by ‘cccplex’ Linux ‘Latest Ubuntu’
Polyline arcs with Width = 2R render as circle segments rather than circle sectors. As Non-reversed arcs these don’t explode. As reversed arc these explode to a single arc rather than a circle sector contour.
There is also still the faulty rendering with Z not zero https://qcad.org/bugtracker/index.php?do=details&task_id=1923
Regards, CVH
|
|
1923 | QCAD (main) | Bug Report | Very Low | Faulty rendering Polylines with Global/Local Widths and... | Assigned | |
1 |
Task Description
Win7pro 32bit Qcad 3.23.0
Andrew, The Arc segments of Polylines with Global or any Local Width render faulty where Global Z or any of the arc’s local Z is not zero.
In the attached drawing setting the Global Z of the inner poly to 5,10,...
The setting of Z to not zero affects the radius of the projected arc and not the bulging of the poly. It also affects the projected widths of the line inversely, but not by changing the widths properties.
Pritty rare combination! True. Qcad is 2D native! True.
Flatten will resolve this.
It is not a purely visual rendering fault, the poly will explode as such.
Maybe similar flaw as with uneven scaling blocks with arcs. https://qcad.org/rsforum/viewtopic.php?f=8&t=5566#p20703
Regards
|
|
2297 | QCAD (main) | Suggestion | Very Low | Few UI inconsistencies | Assigned | |
|
Task Description
1) Line with command prompt in Command Line widget is missing padding/margin - letter C is glued to frame. 2) In the “Selection Filter” widget there is an “whitespace” character before colon “:” symbol on multiple places, it doesn’t seem repeat anywhere else
|
|
1974 | QCAD (main) | Bug Report | Very Low | File > Print Preview: Cannot move paper in new drawing | Unconfirmed | |
|
Task Description
Yesterday I set up a Windows 64 bit install of QCAD Pro which shows the same bug I have been seeing for a while in the Community linux git repo.
Create a new drawing and then go to “Print preview”. Enable “Move paper postion”, the cursor changes to the hand icon, but the paper position is unable to be moved. Only by saving the drawing, exiting the program, restarting and reopening the drawing, will the “Move paper postion” function correctly.
Affected versions tested:
Windows 64bit installer download, as of yesterday. Linux 64bit build from git, about 20minutes ago.
For what it’s worth, this bug is not present in this previous git checkout:
Version: 3.21.1.0 (3.21.1) Internet: QCAD.org Build Date: Jul 2 2018 Revision:
Qt Version: 5.7.0 Architecture: x86_64 Compiler: gcc 6.3.1
Thanks for a great product.
|
|
2440 | QCAD (main) | Bug Report | Very Low | Hatch from Segments > False positives open loop warning... | Assigned | |
1 |
Task Description
Andrew,
Most probably not related to OS or QCAD version.
When hatching an area with Hatch from Segments (HS) there might be false positive warnings on open loops. It seems that this is related to the orientation of the indicated segments and the order of selection. The real problematic position is not always the first that is reported. Loop count is increased even if it is a single loop.
Included a basic test drawing to replicate these. Further details to replicate the issue are in the file.
Regards, CVH
|
|
2505 | QCAD (main) | Feature Request | Very Low | Info > Polygonal Area > Use dimension decimal format fo... | Assigned | |
1 |
Task Description
Andrew, On behalf of user Kmeelo
Polygonal Area adds measurements text with 12 decimal digits and then as short as possible.
Current formatting path see: https://www.qcad.org/rsforum/viewtopic.php?f=32&t=10450&p=42833#p42805
Related forum feature request: https://www.qcad.org/rsforum/viewtopic.php?f=31&t=10458
I also see a misconception of the term ‘precision’. Numbers precision is the amount of significant digits disregarding the position of the decimal point. 12 decimal digits is about the largest precision for numbers with 5 integer digits.
Regards, CVH
|
|
2494 | QCAD (main) | Bug Report | Very Low | Information scrip on drawing screen unaligned. | Waiting on User | |
|
Task Description
Please view the attachment.
Regards
Graeme
|
|
1691 | QCAD (main) | Bug Report | Very Low | Issue with Layouts after "File-Revert" | Assigned | |
|
Task Description
QCad 3.19.2 Professional, 64bit, Liux Mint
Case: 1. Open some saved drawing with viewport entities on layout block (paper space). Print Preview mode is “On” automatically. 2. After “File-Revert” drawing is reopened on layout block (paper space), but now Print Previw mode is “Off” .
For example can try on “flange.dxf”
|
|
2415 | QCAD (main) | Bug Report | Very Low | Issues with OffsetBothSides | Assigned | |
1 |
Task Description
Andrew,
I can’t find any documentation concerning OffsetBothSides under Misc .. Modify. It is not listed in the QCAD features nor in the changelog.
There was a Feature Request FS#1130 for this, I think you might want to close that as being implemented.
The tool asks for a Line, Arc, Circle, Ellipse, Spline or Polyline. It also seems to act on shapes that can be exploded to such entities like Text, Dimension and Hatch entities.
There may be many ‘Result loop not closed’ or ‘No offsets possible’ warnings when hovering over entities on a drawing. The preview may be partially, one or two sided and even two sided partially and closed with semi-circles.
I only successfully created a dual offset for open Splines, open or logically open Polylines. All other attempts result in a single offset at the indicated side.
There are the usual exceptions for Polylines with arc-segments but that is related to small arc segments and being tangentially connected. Only tested it on a Win7 platform. I don’t suspect that version 3.27.8 includes a fix for that ...
Regards, CVH
|
|
2146 | QCAD (main) | Suggestion | Very Low | Keep 'Invisible' objects invisible while saving | Assigned | |
1 |
Task Description
QCAD Professional Win installer 32bit Version: 3.25.2.4 (3.25.2.4) Internet: QCAD.org Build Date: Nov 18 2020 Revision: 40f4475 Qt Version: 5.13.2 Architecture: i386 Compiler: Unknown
Related topic: https://qcad.org/rsforum/viewtopic.php?f=33&t=7882 Explanation found in REntity.cpp Listed as a Public Member Functions inherited from RObject
Regards, CVH
|
|
2452 | QCAD (main) | Feature Request | Very Low | Keyboard Shortcut for Undo Last Point While Drawing Spl... | Assigned | |
1 |
Task Description
Instead of having to click on the toolbar, it would be useful to have a keyboard shortcut for undoing the last fit point (or control point) while drawing splines. Preferably it would also be nice to allow the user the ability to set what the keyboard shortcut is for this function.
|