QCAD Bugtracker

1. Create spline
2. Move spline nodes. After ~10 times move qcad is crashed with backtrace:
Thread 9 “Thread (pooled)” received signal SIGSEGV, Segmentation fault.
[Switching to Thread 0x7fff56dc9640 (LWP 8224)]
0x00007ffff66fabf2 in QList<QSharedPointer<RShape> >::node_copy (this=<optimized out>, src=0x55537c59e758, to=0x555557f66408, from=0x55537cfdc848) at /usr/include/qt5/QtCore/qlist.h:492
492 current→v = new T(*reinterpret_cast<T*>(src→v));
(gdb) bt
#0 0x00007ffff66fabf2 in QList<QSharedPointer<RShape> >::node_copy (this=<optimized out>, src=0x55537c59e758, to=0x555557f66408, from=0x55537cfdc848)

  at /usr/include/qt5/QtCore/qlist.h:492

#1 QList<QSharedPointer<RShape> >::detach_helper (alloc=<optimized out>, this=0×555557311620) at /usr/include/qt5/QtCore/qlist.h:835
#2 QList<QSharedPointer<RShape> >::detach_helper (this=0×555557311620) at /usr/include/qt5/QtCore/qlist.h:849
#3 QList<QSharedPointer<RShape> >::detach (this=0×555557311620) at /usr/include/qt5/QtCore/qlist.h:178
#4 QList<QSharedPointer<RShape> >::detach (this=0×555557311620) at /usr/include/qt5/QtCore/qlist.h:178
#5 0x00007ffff686182a in QList<QSharedPointer<RShape> >::end (this=<optimized out>, this=<optimized out>) at /usr/include/qt5/QtCore/qlist.h:342
#6 QList<QSharedPointer<RShape> >::last (this=0×555557311620) at /usr/include/qt5/QtCore/qlist.h:364
#7 RSpline::appendToExploded (this=0×555557311510, line=...) at math/RSpline.cpp:964
#8 0x00007ffff6867059 in RSpline::getExploded (this=0×555557311510, segments=1457293328) at math/RSpline.cpp:919
#9 0x00007ffff686682a in RSpline::getLength (this=this@entry=0×555557311510) at math/RSpline.cpp:1026
#10 0x00007ffff6c11490 in RSplineData::getLength (this=<optimized out>, this=<optimized out>) at /usr/src/debug/qcad-3.27.0.0/src/entity/RSplineData.h:178
#11 RSplineEntity::getProperty (this=0x5555573114a0, propertyTypeId=..., humanReadable=<optimized out>, noAttributes=<optimized out>,

  showOnRequest=<optimized out>) at /usr/src/debug/qcad-3.27.0.0/src/entity/RSplineEntity.cpp:253

#12 0x00007ffff67cc214 in RPropertyEditor::computePropertyValue (ccProp=...) at /usr/src/debug/qcad-3.27.0.0/src/core/RPropertyEditor.cpp:574
#13 0x00007ffff67d298f in QtConcurrent::FunctionWrapper1<void, RProperty&>::operator() (u=..., this=0x555557757f18)

  at /usr/include/qt5/QtConcurrent/qtconcurrentfunctionwrappers.h:80

#14 QtConcurrent::MapKernel<QList<RProperty>::iterator, QtConcurrent::FunctionWrapper1<void, RProperty&> >::runIteration (it=..., this=0x555557757ee0)

  at /usr/include/qt5/QtConcurrent/qtconcurrentmapkernel.h:68

#15 QtConcurrent::MapKernel<QList<RProperty>::iterator, QtConcurrent::FunctionWrapper1<void, RProperty&> >::runIterations (this=0x555557757ee0,

  sequenceBeginIterator=..., beginIndex=<optimized out>, endIndex=15) at /usr/include/qt5/QtConcurrent/qtconcurrentmapkernel.h:77

#16 0x00007ffff67d2c9d in QtConcurrent::IterateKernel<QList<RProperty>::iterator, void>::forThreadFunction (this=0x555557757ee0)

  at /usr/include/qt5/QtConcurrent/qtconcurrentiteratekernel.h:255

#17 0x00007ffff44b5b2d in QtConcurrent::ThreadEngineBase::run (this=0x555557757f20) at qtconcurrentthreadengine.cpp:302
#18 0x00007ffff59c8d52 in QThreadPoolThread::run (this=0x555556198b10) at thread/qthreadpool.cpp:100
#19 0x00007ffff59c5a61 in QThreadPrivate::start (arg=0x555556198b10) at thread/qthread_unix.cpp:329
#20 0x00007ffff546c717 in start_thread (arg=<optimized out>) at pthread_create.c:435
#21 0x00007ffff54f018c in clone3 () from /lib64/libc.so.6
(

QCAD Professional
Win installer 32bit
Version: 3.25.2.7 (3.25.2.7)
Internet: QCAD.org
Build Date: Dec 16 2020
Revision: e06f230
Qt Version: 5.13.2
Architecture: i386
Compiler: Unknown

Documented in 3.25.2.4, reproducible under 3.25.2.7
In the attached file:
→ Explode the trial cases and locate NaN Widths.
→ These faulty widths are cleared while saving and reverting.
= work around.

Related Post: https://www.qcad.org/rsforum/viewtopic.php?t=7902#p30902
Related Topic: https://www.qcad.org/rsforum/viewtopic.php?t=7901
Related Commit: https://github.com/qcad/qcad/commit/fcd7929bced7ae328029c1aa2ee2aff2745709c6

Arctic_Eddie reports failing CAM offset at exactly these points !!!
Reported is a faulty arc with radius of over 360,000mm.
- I can not reproduce this under QCAD working further on the Polys with NaNs.
- However the direct offset of such controlpoint Splines is erroneous.
(see file in post 30902)

Arctic_Eddie reports arc radii of over 10,000mm.
- These don’t seem to be faulty.
- I agree that BiArc fitting should be bound to a lower and certainly to an upper limit.
- That should be huge otherwise faint curvature is represented by many
wobbles or too quick by straight lines.
(All this, keeping in mind that QCAD doesn’t return the optimum fitted BiArc, see: https://www.qcad.org/rsforum/viewtopic.php?t=4859)

Regards,
CVH

Andrew,
For more detailed description please refer to:
https://www.qcad.org/rsforum/viewtopic.php?f=33&p=40081#p40081

In the included screen grab below, left is when drawn cubic, closed periodic, from 4 points.
Right is when the file is re-loaded.

It is hard to select the incorrect shape when pointing near it ... Probably it is referring to the correct internal shape.
After drawing it explodes to a Null length polyline with 2 identical vertices.

I can’t include the error in a file as it reverts on re-load.

The same issue exist for quadratic, closed periodic, from 3 points.

Regards,
CVH

QCAD/CAM
Trial package Win installer 32 bit
Version: 3.25.2.0 (3.25.2)
Internet: QCAD.org
Build Date: Sep 4 2020
Revision: 4a61501
Qt Version: 5.13.2
Architecture: i386
Compiler: Unknown

Local decimal separator is ‘,’ (comma)
In CAM configuration .. Z Levels .. Safety level

Using nn,nnn the output is Nxx G0 Znn
Using nn.nnn the output is Nxx G0 Znn.nnn

Drop down boxes are all in dot format.
Didn’t try anything else yet

Regards,
CVH

In my example I can’t draw a circle with circletangent2 if the defining point is on one of the defining tangents. The tangency is lost when I try to do this.

I attached 4 screenshots: TheExample.png, TryingPoint1.png, TryingPoint2.png and The_Point_Isn’t_On_The_Tangents.png.

Hallo Andrew,

Found a bug in the 3D Simulator execution

Hi Andrew,

Still working on creating HPGL.PLT toolpaths for the HP7580 pen plotter. QCAD has some trouble creating toolpaths. Too often it shuts itself down, or the PC gets stalled.

Recreating the same error however is possible

Andrew,

The _DatumFilled Block used by Datum entities (DT) is considered as not used and is purged by Purge Unused Blocks (BP).
There is no block association for these special types of arrowheads in QCAD.

After purging the Datums are not immediately updated but the special arrowheads will eventually disappear. Adding new Datums will not fix that.

Not problematic because the _DatumFilled Block is re-created on save/reload when Datum entities exists. Datums are updated.

Probably not OS or version related.
Related forum topic: https://www.qcad.org/rsforum/viewtopic.php?f=89&t=10694

Best solution would be to support different types of arrowheads and all related:
https://qcad.org/bugtracker/index.php?do=details&task_id=695 https://qcad.org/bugtracker/index.php?do=details&task_id=757 https://qcad.org/bugtracker/index.php?do=details&task_id=1157

Regards,
CVH

If a file is opened by clicking on it in an open ZIP archive, autosave will not work.

Linux Mint -64

Autosave function not working, error warning given instead!

I see the following problem:
When I open a particular DXF file in the Professional Trial version 3.27.9.0 on macOS, “^I” in text fields is expanded to whitespace.
When I open the same DXF file in the Community Edition 3.27.9.0 on NetBSD/x86_64 (installed from pkgsrc), “^I” in text fields is visible as “^I”.

Case:

Select a block array,
put it with “Copy with reference” or “Cut with reference” into the clipboard,
choose a reference point which isn’t in the center of the array,
use the paste tool / with option “flip pasted entities”

If I flip only in horizontal or vertical direction the preview box will double in size and I can’t place the entities precisely regarding to the reference point.
If I try to flip in both directions at the same time - you can’t see this effect.

Windows
3.0.8
Application preferences > Graphics View > Appearance - Solid grid lines doesn’t change anything?

See http://www.qcad.org/rsforum/viewtopic.php?f=11&t=2274&view=unread#unread

Windows 7-64
3.0.7
When adding or removing additional viewports,an extra unnecessary window of the viewport is created.

Hallo Andrew,

testing the drill toolpath I used single point markers.

In 3D simulation the tool drills the toolpath AND uses the drill as a mill.

Cam Export and generated G-code is not effected.

QCAD Professional
Windows 7, Win installer 32bit
Version: 3.25.2.7 (3.25.2.7)
Internet: QCAD.org
Build Date: Dec 16 2020
Revision: e06f230
Qt Version: 5.13.2
Architecture: i386
Compiler: Unknown

Issues most likely unrelated to OS and installations before 3.25.
Related post:
https://qcad.org/rsforum/viewtopic.php?&t=7982

Flaws documented in full in attached dxf.
The dxf has meaningful Layer States.

4 Columns:
- Prior Art
- The test cases
- Actual results
- Results with proposed fix

Tried as many things as I can come up with.
Orange: Flaws
Red: Errors
Green: Good results (or as good as I can get them)

Solution(s) given in attached script explode.js
(I am just a simple guy and wouldn’t know how to file a pull request on GitHub ......)

In section: “explode polyline into line and arc segments”
group: “if (RPolyline.hasProxy() && polyline.hasWidths()) {....}”
All additions, updates & typos are marked with “CVH”, one can textual search for it.
Over-documented for sure.
Any Eaction is to debug in Windows and is obsolete.

Included PreferencesPage.ui is updated for the all Splines from Text fix
Still in consideration: Forcing cubic splines from text to degree 2 ...
... I am rather convinced ...

CVH

Andrew,

A user essentially pointed out to an ACAD textbook example.
https://qcad.org/bugtracker/index.php?do=details&task_id=2533
Step 3 of: https://autodesk.blogs.com/between_the_lines/2012/07/drawing-with-surveyors-units-in-autocad.html

Please refer to this topic:
https://www.qcad.org/rsforum/viewtopic.php?f=33&t=10652

Regards,
CVH

Open QCAD and the application preferences. In the section “General: tool settings " you can resize the columns: Menu, Shortcuts etc.
The problem is that it is not intuitive. The first divider is not selectable and the second moves the first, only backwards.