Adding Options to the CAM Configuration Page
Moderator: andrew
Forum rules
Always indicate your operating system and QCAD version.
Indicate the post processor used.
Attach drawing files and screenshots.
Post one question per topic.
Always indicate your operating system and QCAD version.
Indicate the post processor used.
Attach drawing files and screenshots.
Post one question per topic.
Re: Adding Options to the CAM Configuration Page
I found out what my problem was, the QComboBox needed the Editable property to be checked.
Onwards I go...
JT
Onwards I go...
JT
Re: Adding Options to the CAM Configuration Page
I was working on a post for my plasma table that runs on linuxcnc and had some trouble. i have made some boxes under configuration options global that i named "cutheight" "piercehight" "safeight" and i want the numbers from these boxes to be in my g-code in brackets as seen in the tooldown section where i call a subroutine (o<touchoff> call [8] [0] [3]) as in the example here:
G64 P0.05 G21 S100
G00 X10 Y0 F1000
o<touchoff> call [8] [0] [3]
G01 X20
G03 X30 Y10 I0 J10
G01 Y190
G03 X20 Y200 I-10 J0
G01 X10
G03 X-0 Y190 I0 J-10
G01 Y10
G03 X10 Y-0 I10 J-0
M5
G92.1
G0 Z50
M2
But as far as i can see jthornton has been working on a post that are doing almost the same thing, has he got this up and running?
G64 P0.05 G21 S100
G00 X10 Y0 F1000
o<touchoff> call [8] [0] [3]
G01 X20
G03 X30 Y10 I0 J10
G01 Y190
G03 X20 Y200 I-10 J0
G01 X10
G03 X-0 Y190 I0 J-10
G01 Y10
G03 X10 Y-0 I10 J-0
M5
G92.1
G0 Z50
M2
But as far as i can see jthornton has been working on a post that are doing almost the same thing, has he got this up and running?
Re: Adding Options to the CAM Configuration Page
Please indicate what version of QCAD/CAM you are using. QCAD/CAM >= 3.17.0 has been updated considerably in terms of handling and postprocessor format.
Re: Adding Options to the CAM Configuration Page
I have been using Version: 3.17.0.0 (3.17.0) since the release. i can see that it has a lot of new functions, i have planned to look into this for my mill that has a Fagor 8055 control. But for my plasmatable i was just in the process of adding some functions to my post after an upgrade to my torch height control. the problem i ran into was that the numbers following the name of the subroutine had to be in brackets like this [3] and that made a conflict with the syntax of javascript.
Re: Adding Options to the CAM Configuration Page
I just upgraded from 3.15 to 3.17
None of my custom CAM modules are picked up by the new version. How do I make QCAD aware of my cam configurations?
I copied the files over from the old Camconfigurations folder to the new, but that did not work.
None of my custom CAM modules are picked up by the new version. How do I make QCAD aware of my cam configurations?
I copied the files over from the old Camconfigurations folder to the new, but that did not work.
Re: Adding Options to the CAM Configuration Page
QCAD/CAM 3.17 uses an updated configuration to account for toolpaths, cutter radius compensations, etc. Depending on how much your configurations differ from plain G-Code, porting could be straight-forward or not.qharley wrote:None of my custom CAM modules are picked up by the new version. How do I make QCAD aware of my cam configurations?
Note that you can still use your old configurations if you put them into scripts/Cam/CamConfigurations and use CAM > CAM Legacy Export to export. In other words, the old CAM export function is still available in QCAD/CAM 3.17. However, it does not support any of the new features such as toolpaths, multi-cut, cutter radius compensation, etc.
Re: Adding Options to the CAM Configuration Page
Thanks for the quick reply. I actually found the Legacy button just before your reply and sure enough, my tools were there.
Will port it to the new CAM interface. Looks straight forward enough. I will let you know if I find things that needs custom configuration options.
Will port it to the new CAM interface. Looks straight forward enough. I will let you know if I find things that needs custom configuration options.
Re: Adding Options to the CAM Configuration Page
Why it is my Configuration Options missing "per Layer" options? Just compared my Configuration Options dialog box with the one posted in the first page of this thread and they looks quite different. It is there a manual or something where it is explained how to configure all this things?
Re: Adding Options to the CAM Configuration Page
The first dialog posted is from QCAD/CAM 3.17 or later which is toolpath based (1. create toolpaths from entity selection and assign various CAM related properties, 2. export said toolpaths through a post processor to G-Code etc.).Dacicusan wrote:Why it is my Configuration Options missing "per Layer" options?
The second dialog is from QCAD/CAM 3.16 or earlier (legacy) which can only export the whole geometry in a drawing in one go with identical parameters or to a certain degree use parameters on a layer basis. This legacy export is still available in QCAD/CAM >= 3.17 under CAM > CAM Legacy Export.
The brief QCAD/CAM Tutorial should get you started on QCAD/CAM 3.17 or later:
https://www.qcad.org/doc/qcadcam/QCADCA ... ial_en.pdf
More documentation on QCAD/CAM and creating toolpaths will be made available once the interface stabilizes. QCAD/CAM 3.17/3.18 is still new and might still be undergoing substantial changes in the coming months before stabilizing.