Flyspray:: Flyspray::QCAD Bugtracker: Recently opened tasks https://www.qcad.org/bugtracker/ 2019-05-17T09:22:42Z FS#1886: Support advanced tolerance settings for dimensions 2019-05-17T09:22:42Z 2019-05-17T09:22:42Z

Add support for
- tolerance display (dimtol)
- upper limit (dimtp)
- lower limit (dimtm)
- tolerance precision (dimtdec)
- tolerance text size factor (dimtfac)
- tolerance suppress zeros, etc.

See also:
https://www.qcad.org/rsforum/viewtopic.php?f=33&t=6269

Andrew https://www.qcad.org/bugtracker/:1886
FS#1885: Modify > Edit Text: Text dialog messes up formatting of subscript / superscript 2019-05-10T20:58:24Z 2019-05-10T20:56:30Z

See also:
https://www.qcad.org/rsforum/viewtopic.php?f=33&t=6267

Create text with formatting:

\fArial|b0|i1|c0|p0;R\fArial|b0|i0|c0|p0;\S^2;

i.e. Capital, italic R with subscript 2 (not italic).

Edit text.

Formatting changed to (invalid):

\fArial|b0|i1|c0|p0;R\S^\fArial|b0|i0|c0|p0;2;
Andrew https://www.qcad.org/bugtracker/:1885
FS#1884: File > Bitmap Export: margins despite zero margin settings 2019-05-08T08:53:54Z 2019-05-08T08:52:19Z

A margin of 0px can still lead to a margin if width is much larger than height or vice versa.

See also:
https://qcad.org/rsforum/viewtopic.php?f=33&t=6257

Andrew https://www.qcad.org/bugtracker/:1884
FS#1883: File > SVG Export: invalid SVG comments 2019-05-07T11:43:23Z 2019-05-07T11:40:41Z

SVG / XML output is invalid if text contains “–“.

See also:
https://www.qcad.org/rsforum/viewtopic.php?f=33&t=6254

Andrew https://www.qcad.org/bugtracker/:1883
FS#1882: Found a two bugs in the formation of the text 2019-05-06T04:22:44Z 2019-05-06T04:15:45Z

1.
\fGOST Common|b0|i1|c204|p34|;Text - not correctly recognized in Qcad, displays all content (with last “|”, so forms AutoCAD)
\fGOST Common|b0|i1|c204|p34;Text - normally recognized in Qcad

2.
Line spacing (\pxsm1; \pxsm2; \pxsm3; etc.) is not recognized in Qcad:

\pxsm1;{Text\PText}

output as:

xsm1;Text
Text

freeinform https://www.qcad.org/bugtracker/:1882
FS#1881: Layers issue resurfaces 2019-04-29T08:29:40Z 2019-04-29T06:06:24Z

Layers issue has returned. Add new layer and the new layer, even though active, is not highlighted although the pencil icon shows. And in some cases no layers are highlighted after the new layer is added or the wrong layer is highlighted after adding new layer. 3.22.09

Hugh Blackwood https://www.qcad.org/bugtracker/:1881
FS#1880: Line only trims one end when trimmed to circle 2019-04-25T14:06:29Z 2019-04-25T14:03:47Z

using the trim (RM) command
the drawing has a circle with a line going through it. I want to trim the line ends to the circle with the remaining lines inside the circle.
select the circle as limiting entity.
command line says Choose entity to trim. click the line on the right side of center, the excess line on the right is properly trimmed.
command line says Choose entity to trim. Click the remaining line inside the circle on the left side of center. nothing happens.

if I exit the trim command and re-enter, now I can trim the left side of the line

Larry Buller https://www.qcad.org/bugtracker/:1880
FS#1879: File > PDF Export: print preview unclosable 2019-04-25T12:17:32Z 2019-04-25T12:17:15Z

If the print preview is opened automatically using File > PDF Export, the print preview does not open correctly or is unclosable (script exception).

Andrew https://www.qcad.org/bugtracker/:1879
FS#1878: Snap > Distances from 2 Points: snap to point with given distances to two points 2019-04-16T15:50:32Z 2019-04-16T15:50:32Z

See also:
https://www.qcad.org/rsforum/posting.php?mode=reply&f=32&t=6211

Andrew https://www.qcad.org/bugtracker/:1878
FS#1877: Post Processor Tutorial 2019-04-15T14:14:12Z 2019-04-15T14:14:12Z

Hallo Andrew,

I am still busy on the never ending G-code story. Doing so I wrote a small Post Processor Tutorial for all those nerds who wants to write their own. If you like it you might add it to QCAD. However, since English is not my native tongue I suggest checking it would be wise.

Meanwhile I have downloaded the source code, and could not find the CAM’s Drill-path-script. I am now using a negative Drill Cut Depth to set a Laser Dwell time, were as a field “Dwell Time (in seconds)” in the Drill-path would be more appropiate. Is this script open source available or is it part of ‘closed part’ of QCAD?

H. Stiekema https://www.qcad.org/bugtracker/:1877