QCAD Bugtracker

QCAD - 2D CAD System.

Click here for a documentation of the DokuWiki formatting syntax that can be used in reports

Please search for existing tasks (also closed ones) before opening a new task.

Please make sure that you are using the latest Version of QCAD before posting a bug (menu Help > Check for Updates)

IDCategoryTask TypeSeverity  descSummaryStatusProgress
1940QCAD/CAMFeature RequestLowCAM > CAM Configuration: Add program descriptionAssigned
0%
1 Task Description

Add a program description to the CAM configuration dialog and export to postprocessors as variable.

See also:
https://www.qcad.org/rsforum/posting.php?mode=quote&f=32&p=24649

1954QCAD/CAMReleaseLowRevised PWM Post ProcessorAssigned
0%
Task Description

Hallo Andrew,

I have revised the PWM Post Processor to Revision D.

1971QCAD/CAMBug ReportLowCAD/CAM 3D SimulatorAssigned
0%
Task Description

Hallo Andrew,

Found a bug in the 3D Simulator execution

1972QCAD (main)Bug ReportLowHatch import fails for boundaries with many very small ...Assigned
0%
Task Description

See also:
https://www.qcad.org/rsforum/viewtopic.php?f=33&t=6648

1976QCAD (main)Feature RequestLowEnvelope at offset to a poly toolAssigned
0%
Task Description

See:
https://www.qcad.org/rsforum/viewtopic.php?t=6650

1977QCAD (main)Feature RequestLowCorresponding coordinate format Assigned
0%
Task Description

Hi,

It would be less confusing to read messages in the command line protocol if it would use the same coordinate separators like the settings below Application Preferences / General / Coordinate Format.

This example shows the “Absolute Cartesian Coordinate” but of course all corresponding format settings should be used within messages.

Absolute Cartesian Coordinate: Setting = semicolon (;) but the message will use division (/).

1982QCAD (main)Feature RequestLowmeasure DIN 1356Assigned
0%
Task Description

To measure in the format DIN 1356 , Architect
It is hard work to do this manual input with meta characters.

1983QCAD (main)Feature RequestLowTrim All or Bulk Break outAssigned
0%
1 Task Description

This is a trim method I am missing in Qcad.

20 years ago it existed in CadKey.
You had a bunch of lines or segments.
You defined a (new) line or segment as cutter.
‘Trim All’.
You pointed at the side of the cutter entity to trim all intersecting at that side.

Pritty the same as in this topic:
https://qcad.org/rsforum/viewtopic.php?t=5221

Only in rare cases I can use Husky’s workaround as pro.
It all depends on what else is in the clipping rectangle that is needed to trim all intended.
If of no use all single crossing entities have to be chosen one by one.

Regards,
CVH

1997QCAD/CAMBug ReportLowCan't export gcode, intermittentlyAssigned
0%
Task Description

When I create a simple drawing, I cannot export the gcode until I restart qcad.

general steps to reproduce the issue:
1. open a new drawing
2. Add a letter “D” near the origin in Arial font, about 7mm tall.
3. explode it
4. save the drawing
5. Fill in in the “cam configuration” 6. Select the drawing and generate the tool paths.
7. Hit the “export button” or the menu item.
8. Observe that you see the “camexport” command appears in the command section, but there is no file generated for the gcode.

If you restart qcad, then the gcode will export as expected. Also, it appears to work for more complicated drawings. I had the same issue, when I tried to generate the same thing, but using the string “November 2019” at 5mm height. I am using up to date MX Linux with kernel version 4.19.0. I also observed this behavior under Windows 10 professional.

1999QCAD (main)Feature RequestLowViewport: Add additional properties for controlling dim...Assigned
0%
1 Task Description

When working with multiple Viewports with different scale it could be very useful to have extra properties controlling how dimensions are rendered in the viewport:

1)
E.g an extra “Dimension Scale” under “Scale” in the Viewport selection’s ‘Specific Properties’ section, could allow having the same size when printed.
This Dimension Scale would be multiplied on top of the Scale value, but only for Dimensions rendering.

2)
Toggle button for hiding any dimensions in the Viewport. Maybe this should be controlled by being able to specify a Layer that should be hidden in this Viewport only, then I could select my Dimensions layer here.

The Viewport properties:
https://i.imgur.com/s07JtaB.png

2011QCAD (main)SuggestionLowUnable to build 3.23.0.10 with system SpatialIndexAssigned
0%
Task Description

Building with the bundled version, 1.8.5, works fine.

When I try to build using the system version, which for Mageia Cauldron is 1.9.3, the build fails.

https://raw.githubusercontent.com/kekePower/mmbl/master/qcad/2019/12/11/20%3A13%3A48/log.qcad

Here is the current spec file for version 3.23.0.4.
https://svnweb.mageia.org/packages/cauldron/qcad/current/SPECS/qcad.spec?revision=1465894&view=markup

It looks like qcad is incompatible with versions above 1.8.5.

Are there plans to port to the new version?

Thanks in advance.

752QCAD (main)Feature RequestVery LowAdd support for the 3dConnexion Space Navigator (Pan an...Assigned
0%
3 Task Description

The 3dConnexion Space Navigator would be wonderful as a pan and zoom control. I find it extremely useful in SketchUp and when I switch from that to QCAD am always disappointed to find it doesn’t work.

3dconnexion DOT com/buy/shop.html?3dxcp=GA_GA_search_google_US_Brand

While full support for the buttons and such would be nice, just the ability to map the axis to pan and zoom would be wonderful.

991QCAD (main)Feature RequestVery LowAdd warning when overwriting custom propertyAssigned
0%
Task Description

Property Editor - Geometry - Custom - Add Custom Property

If I use an identical Name accidentally again in the Custom Property dialog - it will overwrite the first value with the same name without any warnings.

1426QCAD (main)Feature RequestVery LowLoad drawings that were open when closing QCAD on start...Assigned
0%
Task Description

See also:
http://www.qcad.org/rsforum/viewtopic.php?f=31&t=4249

1443QCAD (main)Bug ReportVery LowView > Status Bar remains uncheckedAssigned
0%
Task Description

Status Bar menu remains unchecked even it is toggled on or off

1626QCAD (main)Feature RequestVery Low'Clip to Circle' toolAssigned
0%
1 Task Description

Hi Andrew,

Would it be possible to have a clip to circle tool also please?

Regards

Clive

1649QCAD (main)Feature RequestVery LowAdd configuarable format options for saving blocks to l...Assigned
0%
Task Description

Add configuarable format options in application preferences for saving blocks to library to either dxf or dwg.

1691QCAD (main)Bug ReportVery LowIssue with Layouts after "File-Revert"Assigned
0%
Task Description

QCad 3.19.2 Professional, 64bit, Liux Mint

Case:
1. Open some saved drawing with viewport entities on layout block (paper space). Print Preview mode is “On” automatically.
2. After “File-Revert” drawing is reopened on layout block (paper space), but now Print Previw mode is “Off” .

For example can try on “flange.dxf”

1719QCAD (main)Bug ReportVery LowUndo on converted drawing leads to wrong label position...Assigned
0%
Task Description

Drawing converted from inch to mm - undo leads to wrong dim label position. I can fix that with “Reset Label position” but it would be nice if QCAD could to that in first place.

1760QCAD (main)Bug ReportVery LowSelf-crossing polylines can't be cut twice at segment c...Assigned
0%
Task Description

Re-entering dividing problem from  FS#1757 

Divide the poly selecting near segment 1 at the segment crossing.
> A new node is inserted on the crossing and made start and end node.
Divide the poly again selecting near segment 2 at the segment crossing.
> no division appears to be done.

One can’t divide the second segment at the crossing

Presumed intended behaviour like  FS#1750 

Regards

1765QCAD (main)Bug ReportVery LowErrors with polyline offsetAssigned
0%
1 Task Description

Win 7 32 bit QCAD 3.20.1

Ofsset of a base-line with arcs results in massive ammount of errors.
Most of them occur as a cluster of very tiny segments and are part of the offset. (zoom far in at the red circles)
Mostly they occur where the offsetted arcs should merely be trimmend pairwise.
Some occur as detached entities or as detached strings of entities very near the offset (strings not documented).
Spooks occur at opposite site when base-line is not closed.
360° curls can occur with R = Offset.
Null-entities may occur (not documented, hard to find and not able to copy).

The base-line is checked and sound and has mixed tangentially or not tangentially connected arcs.
Offsetting the mother base-line of the base in the file has similar effect but not all and/or different ones.
Also encountered with offseting polys from fonts.
Used to define pocket paths for CNC.
Detected because the CNC driver will not accept Self-crossers, Null-entities or open ends depending on the settings.

Work arround is to explode and select small entities but this does not solves the issues.
1) Choosing the tolerance large enough will detect small segments that should stay.
2) Recombining will generate new ones at the place where the main segments remain crossed.
Cleaning up the paths is a daunting process with some thousand segments for several offsets.

I assume this has an infuence on the CAM part of QCAD too unless the offset method is different.

1788QCAD (main)Feature RequestVery LowNew snap: reference points of a block referencesAssigned
0%
Task Description

I know this was reported and fixed before ...

https://www.qcad.org/bugtracker/index.php?do=details&task_id=843

... but it looks like we have the issue now back with some kind of variation.

If I use the test drawing which I posted in 2013 ( FS#843 ) it works still as expected after it was fixed.

If I create a new block it won’t work in a new drawing nor in the old test drawing - no chance to snap to the Block Reference.

Edit: New Test drawing:

1900QCAD (main)Bug ReportVery LowRemote shares initially not accessible.Assigned
0%
Task Description

My data files are stored on network shares (synology) with a GB link. QCAD Pro is run in Admin mode.

While in my Windows browser all remote shares are accessible (Green), in the QCAD file open menu they are initially shown as not accessible (Red). By accessing a specific drawing file in a remote share, the share will open and turn green.

Same behavior using ‘Open recent’. Always the message is given that the requested file does not exist, and the file is wiped from the ‘Recent Open’ list. Only if the share is first accessed through ‘Open’ with a random file, it will turn and a ‘recent open’ file for that share will open.

Drag and Drop from a remote share will never work.

1905QCAD (main)Bug ReportVery LowView > Property Editor: Changing attribute of block cha...Assigned
0%
Task Description

See also:
https://www.qcad.org/rsforum/viewtopic.php?f=33&t=6367#p23947

1919QCAD (main)Bug ReportVery LowWrong order XY(Z) for Ordinate Dimension in property ed...Assigned
0%
Task Description

Win7pro Qcad Pro 3.22.1.2

In property editor
properties of an Ordinate Dimension

Without Show Z
DefPoint is displayed in order YX?

With Show Z
Origin is displayed in order XZY?
DefPoint is displayed in order YZX?
LeaderEndPoint is displayed in order ZXY?

Regards

1920QCAD (main)Feature RequestVery LowEdit > Application Preferences: Add preference to disab...Assigned
0%
Task Description

See also:
https://www.qcad.org/rsforum/viewtopic.php?f=89&t=6447

1922dwg2bmpFeature RequestVery LowAdd error message when requesting raster for a non-exis...Assigned
0%
Task Description

It would be nice if QCAD spit some kind of warning message when trying to render a layer with a name that doesn’t exist (and perhaps render nothing), rather than silently rendering an empty image. :D

See https://qcad.org/rsforum/viewtopic.php?f=33&t=6453

1923QCAD (main)Bug ReportVery LowFaulty rendering Polylines with Global/Local Widths and...Assigned
0%
Task Description

Win7pro 32bit Qcad 3.23.0

Andrew,
The Arc segments of Polylines with Global or any Local Width render faulty where Global Z or any of the arc’s local Z is not zero.

In the attached drawing setting the Global Z of the inner poly to 5,10,...

The setting of Z to not zero affects the radius of the projected arc and not the bulging of the poly.
It also affects the projected widths of the line inversely, but not by changing the widths properties.

Pritty rare combination! True.
Qcad is 2D native! True.

Flatten will resolve this.

It is not a purely visual rendering fault, the poly will explode as such.

Maybe similar flaw as with uneven scaling blocks with arcs.
https://qcad.org/rsforum/viewtopic.php?f=8&t=5566#p20703

Regards

1974QCAD (main)Bug ReportVery LowFile > Print Preview: Cannot move paper in new drawingUnconfirmed
0%
Task Description

Yesterday I set up a Windows 64 bit install of QCAD Pro which shows the same bug I have been seeing for a while in the Community linux git repo.

Create a new drawing and then go to “Print preview”. Enable “Move paper postion”, the cursor changes to the hand icon, but the paper position is unable to be moved. Only by saving the drawing, exiting the program, restarting and reopening the drawing, will the “Move paper postion” function correctly.

Affected versions tested:

Windows 64bit installer download, as of yesterday.
Linux 64bit build from git, about 20minutes ago.

For what it’s worth, this bug is not present in this previous git checkout:

Version:
3.21.1.0 (3.21.1)
Internet:
QCAD.org
Build Date:
Jul 2 2018
Revision:

Qt Version:
5.7.0
Architecture:
x86_64
Compiler:
gcc 6.3.1

Thanks for a great product.

Showing tasks 351 - 379 of 379 Page 8 of 8<<First - 4 - 5 - 6 - 7 - 8

Available keyboard shortcuts

Tasklist

Task Details

Task Editing