QCAD Bugtracker

Summary: Block zoomstate supersedes Model_Space after Undo of BC

QCAD Professional
Version: 3.25.2.1 (3.25.2.1)
Internet: QCAD.org
Build Date: Oct 15 2020
Revision: 2895712
Qt Version: 5.13.2
Architecture: i386
Compiler: Unknown «< (Win installer 32 bit)

With the file provided:
ZW to see the top green ‘revision cloud’ up close
QQ
Box select around the cloud
»> 2 entities in selection
BC, select origin somewhere inside the selection, accept proposed naming
»> ‘Block 1’ is created from the selection
TN
BD, select the newly created Block Reference
»> Auto zoom of ‘Block 1’ (Intended behavior)
OO
»> Returns to Model_Space with the zoomstate of the removed Block
»> Halfway down the drawing
»> The former zoomstate of the Model_Space is lost

Intended behavior is that the zoomstate of Model_Space and Blocks don’t mix
See: https://www.qcad.org/rsforum/viewtopic.php?f=31&t=7797&p=30371#p30378

This proves they do, even if the block doesn’t exists anymore.

Regards,
CVH

PS: 3th trial to enter a suggestion ...

I have created a drawing, where the CENTERS of the most outer lines have a distance of 3.06mm in both X and Y.
The line weight of these outer lines is 0.6mm, so the whole image is 3.06mm + 2* 0.6mm/2 = 3.12mm wide and long (center to center plus half of the line weight on every side).
Additionally in the export there is a frame around the image, making it 3.12 + 2*frame.
The export function however calculates 3.06mm when setting the resolution to 1000Pix/cm, so it does not include the line weights and the outer frame.

Clipping bitmaps to only show a part of the image.

See:
http://www.qcad.org/rsforum/viewtopic.php?f=32&t=3263

Es wäre Arbeitserleichternd wenn ich bei den Optionen für Bemaßungen (Prefix/Postfix) eigene Präferenzen speichern könnte so das diese in allen Zeichnungen von mir verfügbar wären.
Zudem wäre es wünschenswert dieses nicht nur bei den Prefix sondern auch bei den Postfix Angaben nutzen zu können was dann alle(?) Manipulationen erschlagen würde.

Siehe auch:
http://www.ribbonsoft.com/rsforum/viewtopic.php?f=11&t=1966

Zooming in and out is lagging to the point of unusable. This is happening in a layout block with the cursor pointing inside geometry with hatches. When the cursor is pointing outside the geometry zooming works as expected.
The attached file has a very simplified testcase that shows this problem almost in the same way as a more complex drawing with multiple layers and hatches.

edit: I also attached the more complex drawing because it is a bit unclear to me where the lagging stops. Outside the viewport or outside the paper.

I just noticed the selection box has the same problem!

If a file is opened by clicking on it in an open ZIP archive, autosave will not work.

Linux Mint -64

Autosave function not working, error warning given instead!

Automatically set the draw order one lower than the lowest draw order of a border entity when creating a hatch. This should be a user preference, since not everyone might want that behavior.

I would like static information of the drawing (like scale, creation-date, modified-date, revision etc) to be available as automatic labels to be placed in the drawing (with selectable style, font etc)

This would greatly simplify the creatin of title sections in the drawing and making sure it is consistent with the actual drawing and not requiring manual “synchronization”.

it would be ideal to be able to have the option to autohide the side panel to increase the visible drawing space when working on a small screen.

You can apply the command to Lines, PolyLine segments, Arcs, Circles, and Rings:

For linear entities parallel to an axis of the coordinate system, aligned Dimensions (parallel Dimensions) are created. For linear entities not parallel to an axis of the coordinate system, either aligned Dimensions (measuring the absolute distance between two points) or horizontal or vertical Dimensions (measuring the horizontal or vertical distance between two points) depending on where you move the pointer are created.

For curved entities, you can create radial, diameter, linear, angular, and arc length Dimensions.

To dimension entities:

Click Dimension > Auto (or type AutoDimension).
In the graphics area, select an entity to dimension.
Click to place the dimension line.
To use another dimension type for Circles or Arcs, specify an option:
Diameter. Creates a diameter Dimension.
Radial. Creates a radial Dimension for an Arc or Circle.
Linear. Creates a linear Dimension of the diameter of a Circle or an aligned, horizontal, or vertical Dimension between the end points of an Arc.
Angular. Dimensions the angle between the end points of an Arc.
Arc length. Dimensions an Arc length.
Note: The chosen option is the default the next time you use the AutoDimension command.

When you move the pointer during a linear dimensioning, you can:
Lock. Determines the current dimension type (aligned, horizontal, or vertical) regardless where you move the pointer.
Unlock. Unlocks the type of linear dimension used.
Press Enter.

***
In short, when you use this tool you click on an entity and it will know what dimension you’re looking for. For Circles, you can specify in the command window R or D for Radius or Diameter.
This would be extremely useful on large drawings where a lot of dimensioning is to be done. One tool and start clicking on entities for dimensioning.

Ziehe ich mit der Maus eine normale Auswahlbox kann ich Elemente markieren.
Möchte ich einzelne Bereiche wieder herausnehmen muss ich alle Elemente einzeln anklicken (mit gedrückter Shift Taste).
Ich kann zwar dies komfortabler gestalten mit der Select → (De -) Select Contour Funktion welche aber erst über das Menue aufgerufen werden muss.

So wie ich einzelne Elemente mit der Maus auswählen und mit der Shift-Maus Funktion deselektieren kann wäre es schön wenn die Shift Taste auch bei Auswahlbereichen direkt zum deselektieren eingesetzt werden könnte.

Case:

Select a block array,
put it with “Copy with reference” or “Cut with reference” into the clipboard,
choose a reference point which isn’t in the center of the array,
use the paste tool / with option “flip pasted entities”

If I flip only in horizontal or vertical direction the preview box will double in size and I can’t place the entities precisely regarding to the reference point.
If I try to flip in both directions at the same time - you can’t see this effect.

Arrange points on a plan according to an arithmetical, geometrical, logarithmic, customizable variation of distances

Use case:

• Start tool
• Choose one entity of the contour
• If contour is closed, area of closed contour is calculated an printed in the command line history
• Configuration parameters: segment length for arc interpolation

Large files/large entities perform bad in QCad. There are many dxf files that are created with thousand of lines that perform reasonable in other cad’s/cam’s that qcad cannot match.

One very useful tool, that could be added would help to improve qcad performance and at the same time enlarge the dxf quality (by replacing thousand of files by arcs), would be a tool called “arc fit” where, when possible and under a determined possible error margin (user selectable) creates arcs replacing the existing lines.
This would improve the file work in QCad also improves CAM software that would work after QCad, that I think is important for many users.

For example, if it is needed to use qcad to generate toolpaths for letters, after exploding letters, the output is almost impossible to work due to the number of lines that are created. Having arcs instead of lines would greatly improve qcad use.

Windows
3.0.8
Application preferences > Graphics View > Appearance - Solid grid lines doesn’t change anything?

QCAD Professional
Win7 WinInstaller 32bit
Version: 3.25.2.7 (3.25.2.7)
Internet: QCAD.org
Build Date: Dec 16 2020
Revision: e06f230
Qt Version: 5.13.2
Architecture: i386
Compiler: Unknown

Related forum Topic:
https://qcad.org/rsforum/viewtopic.php?t=8015

CVH

Hi Andrew,

we know that you need to have always software performance in your mind to decide which features / tools can / should be implemented and on which way.

I really appreciate your effort to find the best middle way between software features and performance but I think also it’s a tough call to appraise worldwide the overall customer equipment to make the software workable to the best for everybody. That isn’t possible without compromise.

Maybe it would make sense to think about a new dialog in the “Application Preferences” to let the user decide what kind of feature are absolutely needed regarding to his/her work-task / equipment. I don’t mean that you need to cover every single thing but the main “performance jeopardy’s” should be covered with an on/off switch.

Yes I know - that isn’t done in 5 minutes but I think that can make your life easier in the long run and will cover even more customer.

Just my two cents. ;)

See http://www.qcad.org/rsforum/viewtopic.php?f=11&t=2274&view=unread#unread

It would be nice to have an additional Radius Measurement tool with short leads. The current Radius tool shows always the lead line to the center of the radius what is in many cases not useful.

I’m not asking for a workaround

Add support for alternate units for dimension style, for example to display units in mm and in.

QCAD Professional
win installer 32bit
Version: 3.25.2.4 (3.25.2.4)
Internet: QCAD.org
Build Date: Nov 18 2020
Revision: 40f4475
Qt Version:5.13.2
Architecture: i386
Compiler: Unknown

Continued from https://qcad.org/bugtracker/index.php?do=details&task_id=1757
Splitting the old report up ...
Same file.
In the left example one can break out segment (D2):
- removing one of the loops with the ‘remove’ option.
- leaving both without the ‘remove’ option.
Bug?
Without the ‘remove’ option it can’t be undone.

Regards
CVH

QCAD Professional
win installer 32bit
Version: 3.25.2.4 (3.25.2.4)
Internet: QCAD.org
Build Date: Nov 18 2020
Revision: 40f4475
Qt Version:5.13.2
Architecture: i386
Compiler: Unknown

Continued from https://qcad.org/bugtracker/index.php?do=details&task_id=1757
Splitting the old report up ...
Same file.
In the left example one can auto trim (AX):
- The lower loop.
- The top loop.
Bug?
The action on the top loop can’t be undone.

Regards
CVH

QCAD Professional
win installer 32bit
Version: 3.25.2.4 (3.25.2.4)
Internet: QCAD.org
Build Date: Nov 18 2020
Revision: 40f4475
Qt Version:5.13.2
Architecture: i386
Compiler: Unknown

Continued from https://qcad.org/bugtracker/index.php?do=details&task_id=1757
Splitting the old report up ...
Same file.
In the left example one can cut (DI) once.
Cutting the second segment results in NO cut.

Regards
CVH

The Info Tool Polygonal Area is a helpful tool ... but I like to ask for additional options

Yes, the polygonal area makes absolute sense but many times you have just to check a square or rectangle area!

It would be nice and time (click) saving if we could use a “Strg Key” to limit the polygonal area to just a rectangle area.
Two mouse clicks for a rectangle area and done

In addition to that it would be nice to have the possibility to count up or down a couple areas.
E.g. I measure area 1 plus area 2 or area 1 minus area 2 ...
Maybe just with an additional keystroke like + or -

Additional Export function for export/import into 3D Programs like Sketchup etc. (file types like .dae, .3ds, .ddf, .skp).

See also:
http://www.ribbonsoft.com/rsforum/viewtopic.php?f=32&t=2176

If I work in QCAD only with Toolbars (and not with the “Cad Tools” there is nowhere a Button to find for “Create Block from selection”.
If I have to create a Block based on a selection I have to work with the Menu or have to activate the Cad Tools.

But, if I look at the Blocklist menu there is a function (+) to add an empty Block. It would be nice to have this button working for both situation - empty Block or depending on a selection to “Create Block from selection”.

Or alternative an additional Button ...

Anyway - in my opinion would that make the “Blocklist” complete.

Windows 7-64
3.0.7
When adding or removing additional viewports,an extra unnecessary window of the viewport is created.

Please see topic:
http://www.qcad.org/rsforum/viewtopic.php?f=31&p=14209&sid=162973e4a12f58c8116299b62673a520#p14209

An additional option would be useful to paste any given entity a set number of times with even/equal gaps in between.

Property Editor - Geometry - Custom - Add Custom Property

If I use an identical Name accidentally again in the Custom Property dialog - it will overwrite the first value with the same name without any warnings.

Hi.

I’m working currently a lot with files coming from rhino. Qcad can open them properly any also most operations on them work as usual - except the selection methods.

box select from upper left to lower right works as usual.
double click to select all connected entities is broken. (only one entity is selected).
box select from lower right to upper left does not select entities touching the selection box. (nothing is selected)

on mac os nothing is selectable with single click.
on linux single click sometimes fails (nothing is selected after clicking on a line).

thanks for looking into this :)

Martin

Hi!

A friendly request to add an option to disable hatch rendering on “dwg2bmp” conversions.

Depending on the nature of the conversion and the density of the hatch, this may render unintelligible images (see attachments). The option could look like “-t, -nohatch” to indicate hatches should be hidden before rendering. This could potentially become an option too for “dwg2svg” or “dwg2pdf.”

Amazing product, thank you so much!

Wipeout entities can be used to hide rectangular or polygonal sections of a drawing, for example to make space for a label inside a hatch.

See OpenDesign news:
“ODA consolidates support for .dgn and .dwg file formats in Teigha”

The 3dConnexion Space Navigator would be wonderful as a pan and zoom control. I find it extremely useful in SketchUp and when I switch from that to QCAD am always disappointed to find it doesn’t work.

3dconnexion DOT com/buy/shop.html?3dxcp=GA_GA_search_google_US_Brand

While full support for the buttons and such would be nice, just the ability to map the axis to pan and zoom would be wonderful.

Hi, for multi-screen hosts it would be very useful to have additional windows while running the single QCad instance. Other applications like Palemoon, Evolution, Gimp are providing that already.
That would help a lot when working on multiple files and copying blocks between.

Support transformations by transformation matrix for block references.

See also:
https://www.qcad.org/rsforum/posting.php?mode=reply&f=33&t=6333

When drawing or moving objects holding down CTRL should activate ortho snapping as long as CTRL is pressed.

If ortho mode has been active before holding down CTRL should deactivate it (for the time it is beeing pressed).

Add a more versatile way of doing a search and replace for text. Regular expressions maybe?

Would it be possible to have the choice to dock or not dock toolbars - in other words keep them floating, an additional option in the tool settings could be added?

Would it be possible to have the choice of either dashed or solid lines for the large cross hairs?

Would it be possible to have options for:

1.Enable or disable Snap label with text.

2.To have a ‘Snap Marker’ with style and colour choice instead of snap label.

* It would be good for users to have the choice.

For some tools like the Horizontal or vertical line, it would be good to have button options (similar to infinite and ray line buttons) instead of the drop down menus.

Hi Andrew,

Hopefully you might be able to squeeze this one around your busy schedule.

Would it be possible to add in the property editor an option to change a dimension arrow to a point / filled dot and maybe also a tick?

I see you are working on some viewport stuff, I am very much looking forward to testing some of this out ;).

Many thanks

Clive

... please see below:

https://www.qcad.org/rsforum/viewtopic.php?f=31&t=4956

Add more dimension arrow styles (e.g. dots).

See forum thread:
http://qcad.org/rsforum/viewtopic.php?f=31&t=2185

The Midpoint Handles should be used to move Polyline Segments and lines. This would add easy to access stretch functionality.
Combined with a shortcut(hold down shift or alt etc.) to fix the movement to be orthogonal to the line this would bring a lot of extra value.
It would also be possible to to have another shortcut to easily insert nodes to Polylines (again hold shift or alt etc.)

Having leader with numbers and text would be awesome to better interact with the drawing and making BOM lists.

Currently it takes too mush time to make the leaders with text and number bubbles.

Hi Andrew,

Creating G-code for cnc-laser, the laser-tool can not be correctly set at all.

Attached a laser tool proposal

It would be nice if QCAD spit some kind of warning message when trying to render a layer with a name that doesn’t exist (and perhaps render nothing), rather than silently rendering an empty image. :D

See https://qcad.org/rsforum/viewtopic.php?f=33&t=6453