QCAD Bugtracker

QCAD - 2D CAD System.

Click here for a documentation of the DokuWiki formatting syntax that can be used in reports

Please search for existing tasks (also closed ones) before opening a new task.

Please make sure that you are using the latest Version of QCAD before posting a bug (menu Help > Check for Updates)

IDCategoryTask Type  ascSeveritySummaryStatusProgress
1923QCAD (main)Bug ReportVery LowFaulty rendering Polylines with Global/Local Widths and...Assigned
0%
Task Description

Win7pro 32bit Qcad 3.23.0

Andrew,
The Arc segments of Polylines with Global or any Local Width render faulty where Global Z or any of the arc’s local Z is not zero.

In the attached drawing setting the Global Z of the inner poly to 5,10,...

The setting of Z to not zero affects the radius of the projected arc and not the bulging of the poly.
It also affects the projected widths of the line inversely, but not by changing the widths properties.

Pritty rare combination! True.
Qcad is 2D native! True.

Flatten will resolve this.

It is not a purely visual rendering fault, the poly will explode as such.

Maybe similar flaw as with uneven scaling blocks with arcs.
https://qcad.org/rsforum/viewtopic.php?f=8&t=5566#p20703

Regards

1924QCAD (main)Bug ReportLowSweepAngle = 0Assigned
0%
Task Description

Win7pro 32bit Wininstaller Qcadpro 3.23.0

Draw an arc.
Select the arc.
In Property Editor:
Set start angle to 135
Set end angle to 135

SweepAngle = */-360

edit the end angle and add “+360”, hit enter

SweepAngle = 0

An arc with zero sweep is a point.
A point is not an arc.
With the same start and end parameter an arc should have a sweep of +/-360.
As for entries by points or by angles.

Regards

1933QCAD (main)Bug ReportLowAdvanced SVG export file overwrite check doesn't use up...Assigned
0%
Task Description

In the Advance SVG Export dialog, when I edit the filename to be different than the default file that already exists and then clear the checkbox for “Overwrite existing file without asking” just to make sure that I haven’t already created a file with the modified name as well, then I get a popup warning that the export would overwrite the default filename, not the name as edited. In other words, the overwrite check ignored the fact that I edited the filename.

Observed on MacOS Mojave (10.14), but probably applies to all.

1936QCAD (main)Bug ReportLowver 3.23 not saving font informationAssigned
0%
Task Description

The attached file is not saving font preference.
All fonts on the online layer are reported as the standard font. If I highlight one or all of the text entities and change the font to something like Yu gothic light, the property page reports yu gothic light and the screen reflects the changed font.
If I save, close and reload, the fonts for all text is again “standard”.

So then I try to enter new text via the “A” draw text command icon. I select “Broadway.ttf” as the main font in the text entry dialog.
One word “Broadway” is entered as the text. it appears on the upper left of the screen as expected and the font name is Broadway in the property editor. If I look at the dxf file source there is a whole bunch of text styles.
I save and close the file, and then open it again. Now the word Broadway has changed to font name “standard” in the property editor and is very definitely not the Broadway.ttf font.

I am not the originator of the file, I am just trying to change the font. If I start a new file and enter new text the font saves just fine, so I am thinking it is a setting somewhere, but I am unable to find it.

We (me and my customers) use these files for engraving so exact font is critical.

1960dwg2pdfBug ReportLowdwg2pdf command failAssigned
0%
Task Description

Good afternoon, I found a bug.

Source file: B5.dwg.

Command line: .\dwg2pdf.bat -f -a -recompute-dim -ltscale=1 -font-substitution Standard GBK path

After I used the command, the message “Warning: standard font not found” occured. And B5.pdf is not found.
Convert is fail.

1961dwg2pdfBug ReportLowToo many drawings are missingAssigned
0%
Task Description

Hello, I found a bug.

Original file: 006–【武汉会展中心店】一层合用前室.dwg

Converted file: 006–【武汉会展中心店】一层合用前室.pdf

Command line: .\dwg2pdf.bat -f -a -recompute-dim -ltscale=1 -block=布局1 path

Bug description file: problem8.png

As you see. I use dwg2pdf to export the block named “布局1”. There are too many drawings missing.

1971QCAD/CAMBug ReportLowCAD/CAM 3D SimulatorAssigned
0%
Task Description

Hallo Andrew,

Found a bug in the 3D Simulator execution

1972QCAD (main)Bug ReportLowHatch import fails for boundaries with many very small ...Assigned
0%
Task Description

See also:
https://www.qcad.org/rsforum/viewtopic.php?f=33&t=6648

1974QCAD (main)Bug ReportVery LowFile > Print Preview: Cannot move paper in new drawingUnconfirmed
0%
Task Description

Yesterday I set up a Windows 64 bit install of QCAD Pro which shows the same bug I have been seeing for a while in the Community linux git repo.

Create a new drawing and then go to “Print preview”. Enable “Move paper postion”, the cursor changes to the hand icon, but the paper position is unable to be moved. Only by saving the drawing, exiting the program, restarting and reopening the drawing, will the “Move paper postion” function correctly.

Affected versions tested:

Windows 64bit installer download, as of yesterday.
Linux 64bit build from git, about 20minutes ago.

For what it’s worth, this bug is not present in this previous git checkout:

Version:
3.21.1.0 (3.21.1)
Internet:
QCAD.org
Build Date:
Jul 2 2018
Revision:

Qt Version:
5.7.0
Architecture:
x86_64
Compiler:
gcc 6.3.1

Thanks for a great product.

1997QCAD/CAMBug ReportLowCan't export gcode, intermittentlyAssigned
0%
Task Description

When I create a simple drawing, I cannot export the gcode until I restart qcad.

general steps to reproduce the issue:
1. open a new drawing
2. Add a letter “D” near the origin in Arial font, about 7mm tall.
3. explode it
4. save the drawing
5. Fill in in the “cam configuration” 6. Select the drawing and generate the tool paths.
7. Hit the “export button” or the menu item.
8. Observe that you see the “camexport” command appears in the command section, but there is no file generated for the gcode.

If you restart qcad, then the gcode will export as expected. Also, it appears to work for more complicated drawings. I had the same issue, when I tried to generate the same thing, but using the string “November 2019” at 5mm height. I am using up to date MX Linux with kernel version 4.19.0. I also observed this behavior under Windows 10 professional.

173QCAD (main)Feature RequestLowexplode text to lettersAssigned
0%
Task Description

implement

208QCAD (main)Feature RequestLowSVG export: support custom line weightsAssigned
0%
Task Description

Find way to support custom line weights for SVG export. See also forum thread: http://www.ribbonsoft.com/rsforum/viewtopic.php?t=1594

228QCAD (main)Feature RequestLowInsert current date (and other fields)Assigned
0%
2 Task Description

Insert field into drawing that displays current date, file name, ...

275QCAD (main)Feature RequestLowRounding all corners of a polylineAssigned
0%
1 Task Description

Modify - Round - Click polyline - round all corners

277QCAD (main)Feature RequestLowcommand line arguments: allow class name after -execAssigned
0%
Task Description

command line arguments: allow class name after -exec

293QCAD (main)Feature RequestLowmulti-select for blocksAssigned
0%
Task Description

It would be nice if one could select multiple blocks in the block list at once (holding ctrl or ctrl+shift). Main purpose would be to delete them if they are not needed anymore. If possible, the same applies to layers.

316QCAD (main)Feature RequestLowBlocks list and selected blockAssigned
0%
1 Task Description

Wouldn’t it be nice, if selecting a block in model view would somehow highlight (just like clicking a block in the list does) the selected block in the “Block List” window?

(Feature request sounds a little harsh, enhancement proposal would seem more apt.)

355QCAD (main)Feature RequestLowRemember function for dimension OptionAssigned
0%
Task Description

I think it would be nice to have more flexibility for Prefix etc. option (not only the drop down with a given choice) and a remember function for all those fields like postfix and tolerance.

Why Remember Function:
If I use a postfix like <>” in the postfix field I’m only able to use it for this particular dimension type at this time. If I change the type (from Horizontal to vertical or what ever) I have always to repeat my postfix. The same with tolerances.

396QCAD (main)Feature RequestLowBlocks: moving blocks: show bounding boxAssigned
0%
Task Description

Blocks: moving complex blocks with drag and drop should show bounding box as preview

455QCAD (main)Feature RequestLowlogical operations for polylinesAssigned
0%
Task Description

A missing feature in my work are logical operations (combine, intersect, ..) for polylines

Example:
Draw some elements, select them, say combine. The result will be the outline of all elements.

467QCAD (main)Feature RequestLowFeature request for new Arc tool option to add to Arc s...Assigned
0%
2 Task Description

For and behalf of mandrena

To add another Arc tool option in Arc tools set:

1.Specify Start point for Arc.
2.Specify End point for Arc.
3.Specify “Tangent” direction (without being restricted in input field) so you can visually select a point on your desired Tangent line!

500QCAD (main)Feature RequestLowAutohide Side PanelAssigned
0%
1 Task Description

it would be ideal to be able to have the option to autohide the side panel to increase the visible drawing space when working on a small screen.

502QCAD (main)Feature RequestLowPoints on line: enter distance instead of number of poi...Assigned
0%
1 Task Description

Points on line: enter distance instead of number of points as a variant of the tool or as a new tool.

503QCAD (main)Feature RequestLowConvert entities to points with a fixed distanceAssigned
0%
Task Description

Select lines, arcs, ... and convert them to points along the lines, arcs, ... with a fixed distance.

See also forum at:
http://www.ribbonsoft.com/rsforum/viewtopic.php?t=1834

512QCAD (main)Feature RequestLowModify stretch and Restrict orthoAssigned
0%
1 Task Description

The modify stretch tool wants first and second corner, start and end point, then starts afresh. When I turn on restrict horizontally eg to align two points between start and end, the restriction sticks and I have to call restrict none, to be able to perform the next iteration, set the first corner then.

So, in the quest for a comfortable user interface, it was nice, if the modify stretch first/second corners parameter setting was not affected by current restrict/ortho etc. settings. Actually, that does not make any sense at all anyways, does it, a rectangle is defined by two degrees of freedom, isnt it?

514QCAD (main)Feature RequestLowPunktpestimmung Intersection manual muss immer wieder n...Assigned
0%
Task Description

Beispiel:
Zeichnen einer Linie (Line two points) mit Punktbestimmung.
Wähle ich für die Punktbestimmung z.B. “End” bleibe ich in diesem Modus bis ich etwas anderes wähle. Gut ;-)

Wähle ich für die Punktbestimmung “Intersection manual” muss ich dies für jeden Punkt immer wieder neu anwählen. Schlecht :-(

516QCAD (main)Feature RequestLowTo add option to 'print only' selected area.Assigned
0%
2 Task Description

To add the option to ‘print only’ selected area in a drawing.

519QCAD (main)Feature RequestLowPress tab to access first control in options tool barAssigned
0%
Task Description

See:
http://www.ribbonsoft.com/rsforum/viewtopic.php?t=1867

Apparently this was possible in QCAD 2 due to the default behavior of Qt.

525QCAD (main)Feature RequestLowchange the printed symbol of pointsAssigned
0%
Task Description

Hi,

in QCAD3 RC2 points were printed as crosses, in QCAD3 RC4 they are printed as (very little) points. I think this isn’t a bug but a feature. ;-)

It would be nice if one could change this behaviour / select the symbol of points.

Best regards - Stefan

This is a double post of http://www.ribbonsoft.com/rsforum/viewtopic.php?p=5870#5870 as suggested there.

554QCAD (main)Feature RequestLowAuswahlbox sollte auch mit der Shift Taste Bereiche dem...Assigned
0%
Task Description

Ziehe ich mit der Maus eine normale Auswahlbox kann ich Elemente markieren.
Möchte ich einzelne Bereiche wieder herausnehmen muss ich alle Elemente einzeln anklicken (mit gedrückter Shift Taste).
Ich kann zwar dies komfortabler gestalten mit der Select → (De -) Select Contour Funktion welche aber erst über das Menue aufgerufen werden muss.

So wie ich einzelne Elemente mit der Maus auswählen und mit der Shift-Maus Funktion deselektieren kann wäre es schön wenn die Shift Taste auch bei Auswahlbereichen direkt zum deselektieren eingesetzt werden könnte.

564QCAD (main)Feature RequestLowSettings organisation in levelAssigned
0%
Task Description

As an old professional “documentation writer and user inteface designer” but IMHO, I’m not convinced that the “Application preferences” are correctly organised for ease of understanding and using them.
These settings are organised in 2 levels. Some of the first levels have their own settings (e.g. “Graphics view”) while most others don’t (e.g. “Load/save”). May I humbly ;-) suggest some consistency rules :
- no sub-level if there is only one subject
- no items on main level if there are already 1 or more sub-level(s).
For instance :
- sub-level “Default Dimension settings” under “Dimension” is the only sub-level : then move these items under main level “Dimension” and suppress the sub-level ;
- the items under “Graphics view” main level (with several sub-levels)could be in a sub-level named “General” ;
Actually, “Graphics view” main level is the only one which has both its own items and sub-levels ;-))) ?

566QCAD (main)Feature RequestLowShortkey for rectangle text rotationAssigned
0%
Task Description

I would like to get a shortkey like ‘+’ to rotate text at 90° clockwise.

579QCAD (main)Feature RequestLowCopy layers / blocksAssigned
0%
2 Task Description

Duplicate (copy, clone) a layer with or without entities on it. New name can be specified by user.

586QCAD (main)Feature RequestLowFile open dialog with previewAssigned
0%
Task Description

Since this is not supported by Qt anymore, this would likely have to be implemented from scratch.

588QCAD (main)Feature RequestLowBemaßung Prefix Dropdown mit eigenen Vorgaben erweitern...Assigned
0%
Task Description

Es wäre Arbeitserleichternd wenn ich bei den Optionen für Bemaßungen (Prefix/Postfix) eigene Präferenzen speichern könnte so das diese in allen Zeichnungen von mir verfügbar wären.
Zudem wäre es wünschenswert dieses nicht nur bei den Prefix sondern auch bei den Postfix Angaben nutzen zu können was dann alle(?) Manipulationen erschlagen würde.

Siehe auch:
http://www.ribbonsoft.com/rsforum/viewtopic.php?f=11&t=1966

596QCAD (main)Feature RequestLowTool "Lengthen" mit "Total" erweitern oder ....Assigned
0%
Task Description

Eine oft Hilfreiche Zeit/Klick sparende Erweiterung wäre eine “Total” Option bei dem “Lengthen” Tool.

Aktuell ist es mit dieser Funktion möglich ein Element zu verlängern oder zu verkürzen um den Amount X. Der Referenzpunkt (von welchem Ende) kann bestimmt werden.

Die Erweiterung die ich mir wünschen würde wäre auch ein “Total” um ein Element auf eine bestimmte Länge zu bringen ohne einen Taschenrechner benutzen zu müssen. Referenz (welches Ende oder Mitte) sollte (muss) dafür wählbar sein.

Die Funktion “Property editor” stellt bereits über die Geometry Eigenschaften die Möglichkeit zur Verfügung einen “Total” Wert zu manipulieren. Leider bin ich aber hierbei nicht in der Lage zu bestimmen welcher Element Referenzpunkt dafür benutzt werden soll. Könnte ich die Referenz wählen (welches Ende oder Mitte) wäre auch dies dann durchaus akzeptabel ;-)

598QCAD (main)Feature RequestLowSupport tangents between ellipsesAssigned
0%
1 Task Description

To add support for drawing tangents between ellipses.

See topic:
http://www.ribbonsoft.com/rsforum/viewtopic.php?f=31&t=2003

601QCAD (main)Feature RequestLowFür Berechnungen neu zu erstellende Elemente Werte von ...Assigned
0%
Task Description

Es wäre schön wenn ich Werte wie zum Beispiel Längen von Linien direkt abgreifen könnte um diese weiter in Berechnungen verwenden zu können.

Beispiel:
Ich habe eine Linie konstruiert wobei sich eine Länge y ergeben hat.

Nun möchte ich eine Linie zeichnen die 5 mal y sein soll.

Linientool → Wert 5* eingeben und y durch Auswahl mit der Maus von dem vorhandenen Elements übernehmen.

Natürlich könnte ich die Geometrie Info benutzen um den Wert abzulesen oder auch über die Zwischenablage zu benutzen. Ein abgreifen mit der Maus wäre aber schneller, direkter und wahrscheinlich auch mit weniger Fehlern (Human error) verbunden. Wahrscheinlich auch genauer da QCad, denke ich, mit mehr Nachkommastellen rechnet, oder?

604QCAD (main)Feature RequestLowMeasure and record X,Y coordinates tool - add to info ...Assigned
0%
Task Description

Feature request
See topic - http://www.ribbonsoft.com/rsforum/viewtopic.php?f=31&t=2015

Just a thought, but one that could be useful for machinists in particular - a measurement tool that can snap to a point as per usual, but then just displays the drawing coordinates in X and Y. This could be expanded to the dimensions tool set, so that you can click on a point and print the coordinates next to it.

609QCAD (main)Feature RequestLowClean up toolAssigned
0%
1 Task Description

To have a ‘clean up ' tool to:

- eradicate duplicate lines
- eradicate stray points
- remove empty layers
- remove unused blocks

Perhaps with an initial dialog which allows the user to choose what they want to clean up.

612QCAD (main)Feature RequestLowPlot math functionsAssigned
0%
1 Task Description

Input:

  1. X axis min/max or choose line (?) or center (for polar functions)
  2. function: y = f(x) / polar function: r = f(a)

Output:

  1. function plot
614QCAD (main)Feature RequestLowBlocks - overwrite current layer yes/no ...Assigned
0%
Task Description

I would appreciate an option for the library Browser that gives me the possibility to decide by my self to use the current (same name) layer in my drawing or overwrite it with the existing layers in the library item.

Imagine the possibility’s of this feature .... ;-)

617QCAD (main)Feature RequestLowDifferent dimensions font sizes in the same drawing.Assigned
0%
1 Task Description

Different dimensions font sizes in the same drawing.

618QCAD (main)Feature RequestLowuser defined lineweightAssigned
0%
2 Task Description

To have the option to set your own ‘user defined’ line weight.

620QCAD (main)Feature RequestLowoption to have horizontal dimension info using vertical...Assigned
0%
2 Task Description

Some times I need to have the dimension info using the Vertical Dimension tool displayed horizontally.
See attached image:
Possibly this option could be added to the Label drop down menu.

622QCAD (main)Feature RequestLowDisproportianal scaling of arcs, ellipsesAssigned
0%
Task Description

Support disproportional scaling also for arcs, ellipses, other entities, not only lines and polylines with only line segments.

625QCAD (main)Feature RequestLowDistribute block along spline, polyline, ...Assigned
0%
1 Task Description

See:
http://www.youtube.com/watch?v=27bCgg3zLVA

628QCAD (main)Feature RequestLowImprove workflow for entering tool parametersAssigned
0%
Task Description

Provide keyboard shortcuts for options tool bar.

Under Linux, Windows Alt+Key shortcuts can be used.
Mac OS X does not seem to support this.

See also suggestions at:
http://www.ribbonsoft.com/rsforum/viewtopic.php?f=32&t=2053&view=unread#unread

631QCAD (main)Feature RequestLowOption "Scale" für das öffnen von Templates ...Assigned
0%
Task Description

Wenn ich eine Zeichnung plane überlege ich mir natürlich im Vorfeld welche Blattgröße und welchen Maßstab ich verwenden möchte.

Wenn ich Templates (z.B. Zeichnungsblatt A4) für die Blattgröße öffnen könnte und dabei direkt einen Skalierungsfaktor (z.B. 10) vorgeben könnte hätte ich ohne Umwege gleich alles was man braucht. In diesem Fall ein A4 Blatt im Maßstab 1:10.

Im Grunde genommen das selbe was ich bereits mit Library Items machen kann ... ;-)

637QCAD (main)Feature RequestLowViewports / View ListAssigned
0%
Task Description

1. The Scrollbars for each window in the Viewports has the same size like the normal used scrollbars for windows. If you are working on a normal size Monitor it “steals” a lot of “working space”. Is there any possibility to make the scrollbars smaller or just a line to separate the windows so that I have to navigate with Keyboard and mouse?

2. I thing the Viewports and the View List belongs together - is it possible to get a button in the “View List / Tool Bar” to choose a Viewport style instead of “walking” the long way over the “Drawing preferences” Menu?

See also:
http://www.ribbonsoft.com/rsforum/viewtopic.php?f=47&t=2071

Showing tasks 51 - 100 of 382 Page 2 of 8 - 1 - 2 - 3 - 4 - 5 - Last >>

Available keyboard shortcuts

Tasklist

Task Details

Task Editing