QCAD Bugtracker

When I modify partly a DIM with “Stretch” or changing one Extension line position with drag and drop the Value text is updated which is nice working. Unfortunately the previous value stays in place and is overwritten by the actual value. I think for a good readability the previous value should disappear in the moment when the new value is presented.

So far, layer status has only been implemented very rudimentarily.
I wish something like a dialog box in which you can choose for each layer status, which layers belong to it and which not.

It would be so useful to have an option to be able to detect duplicates within a given selection.

It would be useful to have an additional option to only detect duplicates on user defined selection of drawing.
Please see topic:
http://www.qcad.org/rsforum/viewtopic.php?f=32&p=9145#p9145

Add the option to use a fixed path for the save to, open and CAM export directories.

(G code files are usually saved in on directory that the Control Program opens them up from so this would save a ton of mouse clicking)

There is the Synchronize attributes feature which works well. But It affects only block references in the active layout(modelspace, block layout). If I want to synchronize attributes of block references in in another blocks, i have to manually go through all blocks and run synchronize attributes feature. That is the reason I would like to modify Synchronize attributes feature to affect all block references in a drawing, or add new Deep synchronize attributes feature.

Hi,

It would be less confusing to read messages in the command line protocol if it would use the same coordinate separators like the settings below Application Preferences / General / Coordinate Format.

This example shows the “Absolute Cartesian Coordinate” but of course all corresponding format settings should be used within messages.

Absolute Cartesian Coordinate: Setting = semicolon (;) but the message will use division (/).

QCAD Professional
Win installer 32bit
Version: 3.25.2.7 (3.25.2.7)
Internet: QCAD.org
Build Date: Dec 16 2020
Revision: e06f230
Qt Version: 5.13.2
Architecture: i386
Compiler: Unknown

Documented in 3.25.2.4, reproducible under 3.25.2.7
In the attached file:
→ Explode the trial cases and locate NaN Widths.
→ These faulty widths are cleared while saving and reverting.
= work around.

Related Post: https://www.qcad.org/rsforum/viewtopic.php?t=7902#p30902
Related Topic: https://www.qcad.org/rsforum/viewtopic.php?t=7901
Related Commit: https://github.com/qcad/qcad/commit/fcd7929bced7ae328029c1aa2ee2aff2745709c6

Arctic_Eddie reports failing CAM offset at exactly these points !!!
Reported is a faulty arc with radius of over 360,000mm.
- I can not reproduce this under QCAD working further on the Polys with NaNs.
- However the direct offset of such controlpoint Splines is erroneous.
(see file in post 30902)

Arctic_Eddie reports arc radii of over 10,000mm.
- These don’t seem to be faulty.
- I agree that BiArc fitting should be bound to a lower and certainly to an upper limit.
- That should be huge otherwise faint curvature is represented by many
wobbles or too quick by straight lines.
(All this, keeping in mind that QCAD doesn’t return the optimum fitted BiArc, see: https://www.qcad.org/rsforum/viewtopic.php?t=4859)

Regards,
CVH

Andrew,
For more detailed description please refer to:
https://www.qcad.org/rsforum/viewtopic.php?f=33&p=40081#p40081

In the included screen grab below, left is when drawn cubic, closed periodic, from 4 points.
Right is when the file is re-loaded.

It is hard to select the incorrect shape when pointing near it ... Probably it is referring to the correct internal shape.
After drawing it explodes to a Null length polyline with 2 identical vertices.

I can’t include the error in a file as it reverts on re-load.

The same issue exist for quadratic, closed periodic, from 3 points.

Regards,
CVH

Andrew,

One Microinch is equivalent to 25.4 nanometers and I don’t consider that to be metric.

RUnit.isMetric(this.getDocument().getUnit()) returns true for RS.Microinch or value 8.

https://github.com/qcad/qcad/blob/master/src/core/RUnit.cpp#L145-L155
Returns false for: RS::Inch ; RS::Foot ; RS::Mile ; RS::Mil ; RS::Yard
... and true for all the rest.

Also see last note in: https://www.qcad.org/rsforum/viewtopic.php?f=31&t=9506&p=38295

Not to be confused with RDocument::isMetric() because that returns the measurement system unless that is RS::UnknownMeasurement what is rather impossible with drawings created by QCAD.

Regards,
CVH

When dimensioning my drawings I always want the dimensions to be on the dimensions layer.
When adding text I want the text to be on the text layer.
When drawing an infinite line it is always a construction line, therefore I want it to be on the construction line layer.
When drawing a line segment it almost always is on my outline layer.

So I propose a new option to bind certain actions to certain layers.
Whenever those actions are selected the layer should automatically be switched.

I can imagine this being implemented in the General→Tool Settings menu, where the short cuts are defined.

Customer wishes that stacked text used as subscript is rendered differently (i.e. increased text size, lower position for subscript).
This may also apply to superscripts.

See also:
http://www.qcad.org/rsforum/viewtopic.php?f=32&t=2180

QCAD/CAM
Trial package Win installer 32 bit
Version: 3.25.2.0 (3.25.2)
Internet: QCAD.org
Build Date: Sep 4 2020
Revision: 4a61501
Qt Version: 5.13.2
Architecture: i386
Compiler: Unknown

Local decimal separator is ‘,’ (comma)
In CAM configuration .. Z Levels .. Safety level

Using nn,nnn the output is Nxx G0 Znn
Using nn.nnn the output is Nxx G0 Znn.nnn

Drop down boxes are all in dot format.
Didn’t try anything else yet

Regards,
CVH

Not sure how difficult this would be to implement but just wondered if it is possible to have an option in QCAD to change the opacity of a colour ?

related to topic: http://www.qcad.org/rsforum/viewtopic.php?f=83&p=15715&sid=45f0f0679e8257f3cf98f91e4f0c4577#p15715

To have a ‘clean up ' tool to:

- eradicate duplicate lines
- eradicate stray points
- remove empty layers
- remove unused blocks

Perhaps with an initial dialog which allows the user to choose what they want to clean up.

Looks like error, but may be that’s feature request.

CAD software uses typical navigation behavior as:
Wheel = Zoom; Ctrl+Wheel = Scroll up/down; Shift+Wheel = Scroll left/right.

Any other software like browsers, office software (openoffice writer, ms excel and so on), 2d paint software like GIMP (Photoshop and so on) uses other behavior:
Wheel = Scroll up/down; Ctrl+Wheel = Zoom; Shift+Wheel = Scroll left/right.

Users, that intensively use CAD and other software simultaneously prefer to make same behavior in their applications switching CAD scroll to plain mouse wheel.

QCAD’s “Application Preferences”: “Graphics View: Navigation”: “Mouse wheel/ two finger swipe”: “Scroll” allow user to assign scroll up/down to wheel mouse instead of Zoom. But there is mistake Ctrl+Wheel didn’t change to Zoom. Ctrl+Wheel continues to scroll up/down, as the wheel.
Wheel = Scroll up/down; Ctrl+Wheel = Scroll up/down; Shift+Wheel = Scroll left/right. No zoom!

Draw manipulation at this mode like a hell: you need to use wheel in conjunction with Ctrl/Shift to point draw in desired position, than move your hand to +(-) for make desired zoom.

Changeable color of the selection bar in the layer list.
Now the color of the bar is darkblue and the underlaid icons are black and are not readable.

Hi,

in QCAD3 RC2 points were printed as crosses, in QCAD3 RC4 they are printed as (very little) points. I think this isn’t a bug but a feature.

It would be nice if one could change this behaviour / select the symbol of points.

Best regards - Stefan

This is a double post of http://www.ribbonsoft.com/rsforum/viewtopic.php?p=5870#5870 as suggested there.

Automatic change of icons in the Library Browser from black on white to white on black or vice versa depending on the background (white or black; light or dark) in QCAD main window.
See also https://www.qcad.org/rsforum/viewtopic.php?f=31&p=21970#p21970

Would not it be possible to create a kind of template for printing?
We draw our room without cartridge. The cartridge will automatically appear when printed. The scaling could be automatic so that it goes in the A4 and therefore also will post the scale automatically. The name of the play could be the file name, date last saved after it the rest of the information that would be to add somehow (material index, designer, ...).

Original suggestion:

Bonjour,

Ne serait il pas possible de créer une sorte de template lors de l’impression ?
On dessine notre pièce sans cartouche. Le cartouche s’affiche automatiquement lors de son impression. La mise à l’échelle pourrais être automatique pour que ca rentre dans le A4 et donc l’échelle s’afficherai aussi en automatique. Le nom de la pièce pourrais être le nom du fichier, la date du dernier enregistrement après c’est le reste des infos qui serait à ajouter je ne sais comment (matière, indice, dessinateur, ...).

Add a program description to the CAM configuration dialog and export to postprocessors as variable.

See also:
https://www.qcad.org/rsforum/posting.php?mode=quote&f=32&p=24649

Summary: Block zoomstate supersedes Model_Space after Undo of BC

QCAD Professional
Version: 3.25.2.1 (3.25.2.1)
Internet: QCAD.org
Build Date: Oct 15 2020
Revision: 2895712
Qt Version: 5.13.2
Architecture: i386
Compiler: Unknown «< (Win installer 32 bit)

With the file provided:
ZW to see the top green ‘revision cloud’ up close
QQ
Box select around the cloud
»> 2 entities in selection
BC, select origin somewhere inside the selection, accept proposed naming
»> ‘Block 1’ is created from the selection
TN
BD, select the newly created Block Reference
»> Auto zoom of ‘Block 1’ (Intended behavior)
OO
»> Returns to Model_Space with the zoomstate of the removed Block
»> Halfway down the drawing
»> The former zoomstate of the Model_Space is lost

Intended behavior is that the zoomstate of Model_Space and Blocks don’t mix
See: https://www.qcad.org/rsforum/viewtopic.php?f=31&t=7797&p=30371#p30378

This proves they do, even if the block doesn’t exists anymore.

Regards,
CVH

PS: 3th trial to enter a suggestion ...

Andrew,

The _DatumFilled Block used by Datum entities (DT) is considered as not used and is purged by Purge Unused Blocks (BP).
There is no block association for these special types of arrowheads in QCAD.

After purging the Datums are not immediately updated but the special arrowheads will eventually disappear. Adding new Datums will not fix that.

Not problematic because the _DatumFilled Block is re-created on save/reload when Datum entities exists. Datums are updated.

Probably not OS or version related.
Related forum topic: https://www.qcad.org/rsforum/viewtopic.php?f=89&t=10694

Best solution would be to support different types of arrowheads and all related:
https://qcad.org/bugtracker/index.php?do=details&task_id=695 https://qcad.org/bugtracker/index.php?do=details&task_id=757 https://qcad.org/bugtracker/index.php?do=details&task_id=1157

Regards,
CVH

Clipping bitmaps to only show a part of the image.

See:
http://www.qcad.org/rsforum/viewtopic.php?f=32&t=3263

If a file is opened by clicking on it in an open ZIP archive, autosave will not work.

Linux Mint -64

Autosave function not working, error warning given instead!

Andrew,

When switching from Default to Dark mode the text on alternating rows is hardly visible.
We can customize this color.

It would be easier if a proper default color is set on switching to and back.

Perhaps the user preferences can be remembered.
Perhaps only when the contrast would be affected.

Regards,
CVH

Automatically set the draw order one lower than the lowest draw order of a border entity when creating a hatch. This should be a user preference, since not everyone might want that behavior.

it would be ideal to be able to have the option to autohide the side panel to increase the visible drawing space when working on a small screen.

Case:

Select a block array,
put it with “Copy with reference” or “Cut with reference” into the clipboard,
choose a reference point which isn’t in the center of the array,
use the paste tool / with option “flip pasted entities”

If I flip only in horizontal or vertical direction the preview box will double in size and I can’t place the entities precisely regarding to the reference point.
If I try to flip in both directions at the same time - you can’t see this effect.

Large files/large entities perform bad in QCad. There are many dxf files that are created with thousand of lines that perform reasonable in other cad’s/cam’s that qcad cannot match.

One very useful tool, that could be added would help to improve qcad performance and at the same time enlarge the dxf quality (by replacing thousand of files by arcs), would be a tool called “arc fit” where, when possible and under a determined possible error margin (user selectable) creates arcs replacing the existing lines.
This would improve the file work in QCad also improves CAM software that would work after QCad, that I think is important for many users.

For example, if it is needed to use qcad to generate toolpaths for letters, after exploding letters, the output is almost impossible to work due to the number of lines that are created. Having arcs instead of lines would greatly improve qcad use.

Windows
3.0.8
Application preferences > Graphics View > Appearance - Solid grid lines doesn’t change anything?

QCAD Professional
Win7 WinInstaller 32bit
Version: 3.25.2.7 (3.25.2.7)
Internet: QCAD.org
Build Date: Dec 16 2020
Revision: e06f230
Qt Version: 5.13.2
Architecture: i386
Compiler: Unknown

Related forum Topic:
https://qcad.org/rsforum/viewtopic.php?t=8015

CVH

Hi Andrew,

we know that you need to have always software performance in your mind to decide which features / tools can / should be implemented and on which way.

I really appreciate your effort to find the best middle way between software features and performance but I think also it’s a tough call to appraise worldwide the overall customer equipment to make the software workable to the best for everybody. That isn’t possible without compromise.

Maybe it would make sense to think about a new dialog in the “Application Preferences” to let the user decide what kind of feature are absolutely needed regarding to his/her work-task / equipment. I don’t mean that you need to cover every single thing but the main “performance jeopardy’s” should be covered with an on/off switch.

Yes I know - that isn’t done in 5 minutes but I think that can make your life easier in the long run and will cover even more customer.

Just my two cents. ;)

See http://www.qcad.org/rsforum/viewtopic.php?f=11&t=2274&view=unread#unread

QCAD Professional
win installer 32bit
Version: 3.25.2.4 (3.25.2.4)
Internet: QCAD.org
Build Date: Nov 18 2020
Revision: 40f4475
Qt Version:5.13.2
Architecture: i386
Compiler: Unknown

Continued from https://qcad.org/bugtracker/index.php?do=details&task_id=1757
Splitting the old report up ...
Same file.
In the left example one can break out segment (D2):
- removing one of the loops with the ‘remove’ option.
- leaving both without the ‘remove’ option.
Bug?
Without the ‘remove’ option it can’t be undone.

Regards
CVH

QCAD Professional
win installer 32bit
Version: 3.25.2.4 (3.25.2.4)
Internet: QCAD.org
Build Date: Nov 18 2020
Revision: 40f4475
Qt Version:5.13.2
Architecture: i386
Compiler: Unknown

Continued from https://qcad.org/bugtracker/index.php?do=details&task_id=1757
Splitting the old report up ...
Same file.
In the left example one can auto trim (AX):
- The lower loop.
- The top loop.
Bug?
The action on the top loop can’t be undone.

Regards
CVH

Hello dear CAM developers!

I need to use the same tool at different spindle speed in a single machining file.
I would deeply appreciate if you could add a Spindle Speed edit field in the CAM Profile Toolpath edit window in order that each Toolpath can have its own Spindle Speed value (same as you did for Feed Rate and Plunge Rate)

FYI, the tool on my concern is a laser who’s power is driven by the Spindle Speed PWM signal.
I need to be able to do both engraving and cutting in a single file.
Alas! this laser tool is defined with a fix and unique number (99).
Therefore I cannot define different laser tools with different speeds.

Many thanks
Best regards.

QCAD Professional
win installer 32bit
Version: 3.25.2.4 (3.25.2.4)
Internet: QCAD.org
Build Date: Nov 18 2020
Revision: 40f4475
Qt Version:5.13.2
Architecture: i386
Compiler: Unknown

Continued from https://qcad.org/bugtracker/index.php?do=details&task_id=1757
Splitting the old report up ...
Same file.
In the left example one can cut (DI) once.
Cutting the second segment results in NO cut.

Regards
CVH

The Info Tool Polygonal Area is a helpful tool ... but I like to ask for additional options

Yes, the polygonal area makes absolute sense but many times you have just to check a square or rectangle area!

It would be nice and time (click) saving if we could use a “Strg Key” to limit the polygonal area to just a rectangle area.
Two mouse clicks for a rectangle area and done

In addition to that it would be nice to have the possibility to count up or down a couple areas.
E.g. I measure area 1 plus area 2 or area 1 minus area 2 ...
Maybe just with an additional keystroke like + or -

If I work in QCAD only with Toolbars (and not with the “Cad Tools” there is nowhere a Button to find for “Create Block from selection”.
If I have to create a Block based on a selection I have to work with the Menu or have to activate the Cad Tools.

But, if I look at the Blocklist menu there is a function (+) to add an empty Block. It would be nice to have this button working for both situation - empty Block or depending on a selection to “Create Block from selection”.

Or alternative an additional Button ...

Anyway - in my opinion would that make the “Blocklist” complete.

Please see topic:
http://www.qcad.org/rsforum/viewtopic.php?f=31&p=14209&sid=162973e4a12f58c8116299b62673a520#p14209

An additional option would be useful to paste any given entity a set number of times with even/equal gaps in between.

Property Editor - Geometry - Custom - Add Custom Property

If I use an identical Name accidentally again in the Custom Property dialog - it will overwrite the first value with the same name without any warnings.

I’ve been able to make this work as proof of concept very easily, but many of the functions are inaccessible/difficult to override from post-processors.

Desired functionality:

1) Enable “Add Profile Toolpath” UI elements all the time (remove setRequiresSelection)
2) CAM Profile Toolpath Dialog: Drop-down menu of available Layers. First option “By Selection Only” 3) “By Selection Only” continues to pass EntityIds of selected objects (existing functionality)
4) Choosing an active Layer will use the Layer as source of EntityIds
5) Any changes to Entities on a Layer will result in those new/removed/changed objects being re-generated without having to manually select and update the tool paths. Either do not recover list of EntityIds from the ToolpathBlock, and instead use “live” each time it’s regenerated, or additional functionality to determine if a LayerId is associated with the Toolpath, and then lookup EntityIds.

I assume the persistence of the Layer selection would be available within the Toolpath, so that it will automatically update EntityIds every time a Toolpath is regenerated, without having to select Entities and updating the toolpath manually.

For large projects, being able to force select objects based upon layer dramatically reduces mistakes and speeds up the workflow.

Thanks

Hi!

A friendly request to add an option to disable hatch rendering on “dwg2bmp” conversions.

Depending on the nature of the conversion and the density of the hatch, this may render unintelligible images (see attachments). The option could look like “-t, -nohatch” to indicate hatches should be hidden before rendering. This could potentially become an option too for “dwg2svg” or “dwg2pdf.”

Amazing product, thank you so much!

When editing an existing toolpath to update the parameters of the selected tool, we can update the Feed Rate and the Plunge Rate, but I couldn’t find any way to update the Spindle Speed.

Even when using the Edit Tool KE button, we can edit parameters of the tool on concern but none of the modification is applied to the current Toolpath because as I see, tools parameters are copied fron tools definitions to a Toolpath only at creation of this Toolpath, but Toolpath are not updated accordingly.

Could you please add an edit field for Spindle Speed in the CAM Profile Toolpath window?

Many thanks’, and best regards.

Suggestion to add spelling checker / spell checker for all text boxes

Would it be possible to have the choice to dock or not dock toolbars - in other words keep them floating, an additional option in the tool settings could be added?

Would it be possible to have options for:

1.Enable or disable Snap label with text.

2.To have a ‘Snap Marker’ with style and colour choice instead of snap label.

* It would be good for users to have the choice.

... please see below:

https://www.qcad.org/rsforum/viewtopic.php?f=31&t=4956