Exception in BreakOut.js

Auto Zoom should not be applied every time you go back and forth between editing a block and the main drawing.
At least, not by default: it just isn’t practical. QCAD2 didn’t do it...

see also http://www.ribbonsoft.com/rsforum/viewtopic.php?f=31&t=2111

Open drawing and Auto Zoom will also use invisible Blocks for the displayed Zoom Factor.

DWG files created with QCAD display really fine now in autocad. There are only two minor issues for ACAD users:

1) ACAD complains, that they were not created with a licensed application. One may not be able to work around that one...

2) ACAD complains, that the file does not specify a codepage. For this one, there should be a way around, shouldn’t it?

I am very happy with the compatibility in the new QCAD. Thank you very much for all the efforts that went into it!

Peter

QCAD has a lot of features and buttons, probably more that the autocad I’ve been using. Therefore the learning curve is too slow. It would be a great boost for the program to have the possibility of having an Autocad skin, and it will attract many new users.

Apply a font name replacement table to a drawing. E.g. change font ‘romanc’ to ‘Arial’, etc.

QCAD introduction Book

User Reference Manual

done

<p>
			The paste command inserts
			the entities previously copied to the
			clipboard. Paste is
...

var actions = RGuiAction.getActions()

BiLibrary.createAndSaveButton(iconSvgFile, pngFile);

<h2>[Title]</h2>
<b>Toolbar:</b>
[icon]
<b>Menu:</b> [Top menu] - [Menu entry]
<b>Hotkey:</b> [two letter code or hotkey]

Autosave

Make interval configurable
Enable / disable
Path (?)

Hi Andrew,

Just a little thing I noticed recently.

My default is set to save as DWG and indeed it does, however the auto-save feedback tells me that the file is saved to DXF, although it actually does save to DWG - no big deal but is this correct feedback?

Many thanks

Clive

Autosave 10min saves every 1min

See:
http://www.ribbonsoft.com/rsforum/viewtopic.php?t=1604

Wenn ich das Autosave System richtig verstanden habe funktioniert es so:

Nach Ablauf der eingestellten Zeit wird eine Datei mit Nummer im angegebenen Zielordner abgelegt.
Diese Nummer ist weder fortlaufend noch sicher auf- oder absteigend - also keinerlei Hinweis im Dateinamen für den Anwender welches nun die letzte Sicherung ist.
Ziel scheint zu sein das man eine Sicherung pro Tag hat, richtig?

Allerdings ist die Anzahl der Sicherungen pro Tag abhängig von der Anzahl der neu gestarteten QCAD Sitzungen. Starte ich das Programm einmal für den ganzen Tag habe ich eine einzige Sicherung von jeder bearbeiteten Zeichnung. Sicherungen haben dann die selbe Nummer und werden deshalb jeweils überschrieben.

Starte ich das Programm 10 mal pro Tag habe ich 10 Sicherungen (vorausgesetzt ich bearbeite die selbe Zeichnung in jeder Sitzung) mit unterschiedlichen und nicht in Reihe laufenden Nummern. Sicherungen können somit nicht überschrieben werden und am ende des Tages könnten leicht zig wenn nicht hunderte Sicherungen gespeichert sein.

Würde nun diese Nummer im Dateinamen ersetzt mit dem aktuellen Datum habe ich eine Sicherung pro Tag unabhängig wie oft ich QCAD an diesem Tag gestartet habe. Zudem kann der Anwender gleich den Sicherungstag im Dateinamen erkennen und muss sich nicht durch die “geändert am” Info sekundengenau kämpfen.

Macht das Sinn?

Now I try the third time to post this .... .... deleted by “wrong token”???????
However ...

Regarding to the online tutorial:

quote:
Opening a CXF Font for Editing

To load an existing CXF font file in QCAD to view and edit its glyphs, simply use the menu File > Open and choose the format filter “CXF Font Files (*.cxf)”. Then choose the font file you want to open. The fonts that come with QCAD are stored in directory “fonts” of your QCAD installation.

quote end

Editing the cxf font in the original QCAD font folder will lead to a error message triggered by the Autosave function:

File access error: “C:/Program Files/qcad-3.22.1-pro-win64/fonts\~~Husky_test_font.dxf”. Access is denied.
[15:34:58] Autosave failed: C:\Program Files\qcad-3.22.1-pro-win64\fonts\~Husky_test_font.dxf

Note: Windows will not save anything in a system folder and the process is terminated by windows.

Solution: Move the cxf font for editing from the QCAD folder to a unprotected folder like Documents/drawings.
After editing is done move it back to the QCAD font folder.

I would like to see an autosave-option which allows to autosave, but which keeps only the latest autosave file (instead of all). So there would be autosave (if something crashes) but the hard disk is not filled up too fast.

QCAD 3.0.5

Case:
Start QCAD → Went to the Menu → File → Open recent → choose a Drawing out of the List → click to open this existing drawing.
Message windows appears: QCAD found an Autosave drawing .... will you open it? I choose NO!!!
I go back to the Menu → File → Open recent → will choose the same Drawing .... but it is not anymore listed!!!
Ok - I’m not lazy ...
... back to the Menu → File → Open → find the original file on my Hard drive → click to open it and get the Warning Message:
“Can not open the File ...... Please check your access rights bla bla bla....”

Question: In this case I’m only able to open the bak file and “Save as” under the old name to get my starting situation back ...?
Just because I said “NO” to load the Backup File in first place ... ?

Temporary directory is cleared out when booting Windows.

Autosnap does not recognize the center of a circle as a reference point.

JJ

Splines with hundreds of control points or fit points can cause hangs when using auto snap near them.

Background color of current layout block (property “ColorSettings/BackgroundColor” of type QColor) is not saved in DXF/DWG.

See also:
https://www.qcad.org/rsforum/viewtopic.php?f=33&t=10049

It would be great to be able select a print style (Page size, printer), and apply it to a batch of .dxf files to do a batch print of a multi-drawing job with separate files. I used this feature a ton in ACAD in my previous job.

When I run bbox with the attached file I get inconsistent results if I run it 6 or 10 times.

Sometimes the size is 448979.2349223149/310815.2964427199 (it thinks that there is an object at 0,0)
sometimes it is 338.0789223148604/302.31644271989353 (this is what I think is correct)

ubuntu@server-a:/opt/qcad-3.25.2-pro-linux-x86_64$ ./bbox test.dwg
QCAD version 3.25.2
Warning: RPropertyTypeId::generateId: property already initialized: 7RObject : “” : “Invisible” 15:59:40: Debug: calling odInitialize
15:59:42: Debug: dropped global XDATA (no res buf): “ViewportCenter” Min: 0/0
Max: 448979.2349223149/310815.2964427199
Size: 448979.2349223149/310815.2964427199

ubuntu@server-a:/opt/qcad-3.25.2-pro-linux-x86_64$ ./bbox test.dwg
QCAD version 3.25.2
Warning: RPropertyTypeId::generateId: property already initialized: 7RObject : “” : “Invisible” 15:59:49: Debug: calling odInitialize
15:59:51: Debug: dropped global XDATA (no res buf): “ViewportCenter” Min: 448641.156/310512.98
Max: 448979.2349223149/310815.2964427199
Size: 338.0789223148604/302.31644271989353

The out redirection file is not located in temp dir but in the batch files location. Due to missing file permissions in “C:\Programs\...” the file cannot be created.

This is a fixed an therefore working version of bbox.bat:

@echo off
qcad.exe -no-gui -allow-multiple-instances -autostart scripts\Pro\Tools\BoundingBox\BoundingBox.js %0 %* 1>%temp%\bbox.log 2>&1

type %temp%\bbox.log
del %temp%\bbox.log

In der Benutzerreferenz für Skalieren wurde irrtümlich das Wort “rotiert” anstatt “skaliert” verwendet

Layer ‘0’ has some special function. E.g. it can not be deleted, it will contain the data of undeleted layers.

I recommend adding some explanations: Explain the function of Layer ‘0’ as third paragraph in chapter 12 of the manual. Further it should be recommended to never use this layer for drawing.

By the way: I consider this to be better than no layer undelete. BUT: is there really not way for a true layer undelete...

Ich verwende QCAD normalerweise unter Windows 7 als Benutzer ohne Privilegien. In diesem Modus zeigt der Bibliothekbrowser keinen Inhalt. Der Pfad zur Bibliothek ist in den Applikationseinstellungen korrekt eingerichtet. Wenn ich auf “Aktualisieren” klicke, läuft der Vorgang ab, aber danach ist immer noch kein Inhalt im Browser sichtbar. Starte ich QCAD als Administrator, habe ich keinerlei Probleme mit dem Bibliothekbrowser. Ich vermute, dass bei der Installation von QCAD die Privilegien nicht richtig gesetzt wurden. Eine Neuinstallation hat allerdings keine Abhilfe geschaffen.

Currently lineweights seem to be available up to 2.11mm,how about extending the range for some bigger lineweights!

Regards

Clive

When exporting bitmap images the crop is just a bit too tight, and is resulting in lost parts of the drawing. In QCAD2 there was a very small padding of pixels around the exported object that prevented that problem.

• Selected entities are exported in the way as they are shown on screen.
• Same applies for highlighted entities.
• See attachment.

Hello,

When I started Q3, I selected a White background in the initial dialog window. I opened a copy of a good Q2 file and saw that ALL entities with Q2 Black/White color where forced to be White. Andrew explains this as a mean to avoid unreadable items against the background colors. Remember I selected White as background ? I guess Black/White entities could be better kept as Black ?

Following Andrew’s advice, in Application Preferences =⇒ Graphics View, I unchecked the Auto correct black and white colors check box. The background settings is white. OK.

I went through a process of changing the White color for several layers to Black. I also had to change the color codes for the hatch areas. For instance, the hatch area layer “055_F_Murs” has “14-76-255 / 255-197-179” values in Q2. Why these values are auto corrected to “30-128-255 / 255-191-127” ?

After these changes, I saved the file, closed Q3 and opened the file again.

Catastrophique ! All “Black/White” layers were back to Black and the hatch colors were back to the “auto corrected” values.

Changing the background color to black then white seemed to solve the problem : the layers kept the Black color. Actually it was just an illusion.

Yesterday too much confident, I spent the whole day, modifying layers to Black, adding new layers also Black or custom color, checking the line weight (replacing the “default” (?) value of 0.25 mm with my preferred default value of 0,00 mm, I’ve posted on the forum about this) and so on. I saved the file, closed it.
To-day, nearly all layers have lost their colors :
- Black ones are again White,
- custom color are “auto corrected” as above for “055_F_Murs”,
- only the standard non Black/White colors are preserved, like Blue, Magenta etc.

At this point, I can’t continue using QCAD 3 with enough reliability as my color settings are always lost. This is why I qualify this bug as CRITICAL.
I don’t want to use a Black background or a Light Blue one. Why do you think all old “green on black VDU” were replaced with “black/color on white” displays, to begin by Apple ?

NB I already reported this but can’t find it in the list (maybe because I forgot to enter a summary ? No warning, happily I had a copy with Notepad), sorry for the duplicate.

industry for any marriage ceremony band that will stand the check of time http://www.askweddingdress.net beach prom dresses , or perhaps a bit of style jewellery that may create a long lasting impression, http://www.askweddingdress.net cocktail dress plus size the topic of tungsten carbide rings swiftly will come up http://www.askweddingdress.net short beach dresses http://www.askweddingdress.net inexpensive summer dresses . http://www.askweddingdress.net chian beach dresses Tungsten carbide marriage ceremony rings have develop into additional and additional preferred for a lot of reputable causes; http://www.askweddingdress.net/flower-girl-dresses.html white flower girl dresses nonetheless, just like all factors in existence they might not be for absolutely everyone http://www.askweddingdress.net mini wedding gowns . These guidlelines concerning the advantages and disadvantages of tungsten rings really should enable you to to ascertain if a wonderful tungsten marriage ceremony band will be the great match for you personally, or in case you may well uncover a greater match having a much more classic piece http://www.askweddingdress.net white bridesmaid dresses . http://www.askweddingdress.net cheap dresses The primary factor to understand about tungsten rings is the fact that in addition to

Created library item does not have the same unit as source drawing.
Zero point is not at chosen reference point.

Vers. 3.2.1, Drawing Unit “inch”!

... it takes the absolute 0 point as reference.

Millimeter works fine!!!

Rest of the units .... I don’t know

Case

delete a Layout Block in Block List - name e.g. ANSI A P,
create a new Layout Block - try to use the deleted name (ANSI A P) again and it will be declined because the “Layout already exists.

Broken due to UI file resource not being found.

Deleted (undone) block attributes are stored to DXF/DWG.

Block attributes are not properly synchronized on QCad 3.16.5 after editing the block in the drawing, in Linux Mint 18.1 and in Windows 10; On Windows as less frequency, the error is intermittent, on Linux is constant. Attach the dxf to test.

Hello, I am not sure if this is a bug or if I use it wrong way. But when I create block with two identical block attributes everything look ok. I Can insert it to drawing, set the value (both will change). But when I use “Synchronize attribute (UY)”, only one will stay. It would be fine if both would stay. But I understand that you probably use tag as identification.

To reproduce the problem just open the attached file and press UY

1) Open the attached dxf file
2) Right click on “vne_vent_odvod_ec_3f” block in Block list and select Copy block
3) Choose name
4) Insert reference of this Copy block to the modelspace
5) Save the file
6) Close and reopen the file

RESULT: Attributes of block references included in the original block are missing in the copied block.
Immediately after insertion of the copied block I can see in the property editor, that block reference attributes are not “conected” to the block reference, but they are still visible. They disappear when the file is reopen.

Alternative way I use to copy this kind of blocks without error: Open block I want to copy, Select all entities, reference copy of them, paste to modelspace, select them in modelspace and choose create block.

See also:
https://www.qcad.org/rsforum/viewtopic.php?f=33&t=6672

Library items created from existing drawings should have the same unit as the drawing. Currently, the unit of newly created library items is ‘None’.