QCAD Bugtracker

QCAD - 2D CAD System.

Click here for a documentation of the DokuWiki formatting syntax that can be used in reports

Please search for existing tasks (also closed ones) before opening a new task.

Please make sure that you are using the latest Version of QCAD before posting a bug (menu Help > Check for Updates)

IDCategoryTask Type  ascSeveritySummaryStatusProgress
 1760 QCAD (main)Bug ReportVery Low Self-crossing polylines can't be cut twice at segment c ...Closed
100%
Task Description

Re-entering dividing problem from  FS#1757 

Divide the poly selecting near segment 1 at the segment crossing.
> A new node is inserted on the crossing and made start and end node.
Divide the poly again selecting near segment 2 at the segment crossing.
> no division appears to be done.

One can’t divide the second segment at the crossing

Presumed intended behaviour like  FS#1750 

Regards

 1762 QCAD (main)Bug ReportVery Low Modify // .... selection of entities on locked layer al ...Closed
100%
Task Description

Not served with the degration to ‘Suggestion’  FS#1759 .
Demanded closing  FS#1759  & re-entered

Locking entities (by layer) to avoid selection,eg. nearby,very close by or on the same spot, does not have the intended influence.

Asumed wrong:
- Modify DI
- Modify B2
- Modify D3
- Modify MT
These 4 need a single entity to be selected and selection of a locked entity is allowed.(=questionable)
The action will allways leed to ‘not allowed’.(=correct)

Questionable:
- Modify RM
- Modify CH
- Modify RN
These 3 need a pair of entities.
RM: Selection of a locked limiting entity is allowed (=questionable), enity to trim not.(=correct)
The action will trim unlocked entities to the locked limiter.(=questionable)
CH & RN: Selection of a pair of entities is allowed.(=questionable)
Trimming if ‘trim’ is on will not occur because locked and leeds to ‘not allowed’.(=correct)
The creation of the bevel or rounding on an active locked layer will not occur because locked and leeds to ‘not allowed’.(=correct)
The creation, except for polyline segments (because locked themself), on an active unlocked layer will be done.(=correct)

Less severe but still questionable: (because these don’t necerally act on the locked entities themselves)
- Modify OF
- Modify OH
- Modify SS
OF: Selection of a locked base entity is allowed.(=questionable)
The preview is casted only if the active layer is unlocked.(=correct)
The creation is only done on an active unlocked layer.(=correct)
OH: Selection of a locked base entity is allowed.(=questionable)
Selection of point references from entities on locked layers is allowed.(=questionable)
The preview is casted only if the active layer is unlocked.(=correct)
The creation is only done on an active unlocked layer.(=correct)
SS: Selection of point references from entities on locked layers is allowed.(=questionable)
Strechting is only done for unlocked entities. (=correct)

 1765 QCAD (main)Bug ReportVery Low Errors with polyline offset Closed
100%
1 Task Description

Win 7 32 bit QCAD 3.20.1

Ofsset of a base-line with arcs results in massive ammount of errors.
Most of them occur as a cluster of very tiny segments and are part of the offset. (zoom far in at the red circles)
Mostly they occur where the offsetted arcs should merely be trimmend pairwise.
Some occur as detached entities or as detached strings of entities very near the offset (strings not documented).
Spooks occur at opposite site when base-line is not closed.
360° curls can occur with R = Offset.
Null-entities may occur (not documented, hard to find and not able to copy).

The base-line is checked and sound and has mixed tangentially or not tangentially connected arcs.
Offsetting the mother base-line of the base in the file has similar effect but not all and/or different ones.
Also encountered with offseting polys from fonts.
Used to define pocket paths for CNC.
Detected because the CNC driver will not accept Self-crossers, Null-entities or open ends depending on the settings.

Work arround is to explode and select small entities but this does not solves the issues.
1) Choosing the tolerance large enough will detect small segments that should stay.
2) Recombining will generate new ones at the place where the main segments remain crossed.
Cleaning up the paths is a daunting process with some thousand segments for several offsets.

I assume this has an infuence on the CAM part of QCAD too unless the offset method is different.

 1767 QCAD (main)Bug ReportVery Low Dimension Leader Closed
100%
Task Description

On print mode, the arrow not appear in the dimension

 1795 QCAD (main)Bug ReportVery Low Quit Menu Item disabled after opening preferences Closed
100%
Task Description

Quit Menu Item disabled after opening preferences.

System: OSX 10.13.6
Qcad version: 3.21.2.0

How to repeat:

  1. Open QCad
  2. Open preferences dialogue “QCad Pro → Preferences”
  3. Close dialogue
  4. The menu item “Quit QCad Pro” is now disabled. See attached screenshot

Repeatability: 100%

 1798 QCAD (main)Bug ReportVery Low Drawing Pref > Linetype > Scale of linetypes matches th ...Closed
100%
Task Description

“Drawing Preferences / General / Linetype / Scale of linetypes matches the scale of each viewport” is checked by default for new drawings, however the option is not applied until you open the “Drawing Preferences / General / Linetype” screen and click OK – no need to change anything, just opening the screen and clicking OK is sufficient.

 1799 QCAD/CAMBug ReportVery Low Postprocessor: sign not forced for negative values roun ...Closed
100%
Task Description

formatValue returns “0” instead of “+0” for negative values that round up to 0 with the configured decimals.

 1804 QCAD (main)Bug ReportVery Low Application Preferences > Tool Settings: Filter for "Vi ...Closed
100%
Task Description

1. Search the Tool Settings for “View” and you will only find “Overlays” without the submenu information.
2. Check View manually without a search will provide the submenu information.

 1806 QCAD (main)Bug ReportVery Low Overlay Toolbar visibility in GUI not saved Closed
100%
Task Description

Switch “Overlay” Toolbar to visible below:
View/Toolbars and Widgets/Toolbars/View/Overlays, place the Toolbar in GUI, restart QCAD and the Toolbar is back to invisible.

 1899 QCAD (main)Bug ReportVery Low View > Auto zoom: zoom to invisible entities in blocks Closed
100%
Task Description

Create and insert a block with entities on layer “0” and layer “1”.

Switch off layer “1”.

Auto zoom zooms to block boundary of all entities, including those on layer “1”.

See also:
https://www.qcad.org/rsforum/viewtopic.php?f=33&t=6336

1900QCAD (main)Bug ReportVery LowRemote shares initially not accessible.Assigned
0%
Task Description

My data files are stored on network shares (synology) with a GB link. QCAD Pro is run in Admin mode.

While in my Windows browser all remote shares are accessible (Green), in the QCAD file open menu they are initially shown as not accessible (Red). By accessing a specific drawing file in a remote share, the share will open and turn green.

Same behavior using ‘Open recent’. Always the message is given that the requested file does not exist, and the file is wiped from the ‘Recent Open’ list. Only if the share is first accessed through ‘Open’ with a random file, it will turn and a ‘recent open’ file for that share will open.

Drag and Drop from a remote share will never work.

 1904 QCAD (main)Bug ReportVery Low File > Bitmap Export: Non-plottable layers not exported Closed
100%
Task Description

File > Bitmap Export does not export non-plottable layers.

See also:
https://www.qcad.org/rsforum/viewtopic.php?f=31&t=6364

1905QCAD (main)Bug ReportVery LowView > Property Editor: Changing attribute of block cha...Assigned
0%
Task Description

See also:
https://www.qcad.org/rsforum/viewtopic.php?f=33&t=6367#p23947

 1919 QCAD (main)Bug ReportVery Low Wrong order XY(Z) for Ordinate Dimension in property ed ...Closed
100%
Task Description

Win7pro Qcad Pro 3.22.1.2

In property editor
properties of an Ordinate Dimension

Without Show Z
DefPoint is displayed in order YX?

With Show Z
Origin is displayed in order XZY?
DefPoint is displayed in order YZX?
LeaderEndPoint is displayed in order ZXY?

Regards

1923QCAD (main)Bug ReportVery LowFaulty rendering Polylines with Global/Local Widths and...Assigned
0%
1 Task Description

Win7pro 32bit Qcad 3.23.0

Andrew,
The Arc segments of Polylines with Global or any Local Width render faulty where Global Z or any of the arc’s local Z is not zero.

In the attached drawing setting the Global Z of the inner poly to 5,10,...

The setting of Z to not zero affects the radius of the projected arc and not the bulging of the poly.
It also affects the projected widths of the line inversely, but not by changing the widths properties.

Pritty rare combination! True.
Qcad is 2D native! True.

Flatten will resolve this.

It is not a purely visual rendering fault, the poly will explode as such.

Maybe similar flaw as with uneven scaling blocks with arcs.
https://qcad.org/rsforum/viewtopic.php?f=8&t=5566#p20703

Regards

 1932 QCAD (main)Bug ReportVery Low Check for update fails to discover new version Closed
100%
Task Description

“Help→Check for QCAD Pro Updates” fails to discover new version. Tested on OSX and Linux versions.

1974QCAD (main)Bug ReportVery LowFile > Print Preview: Cannot move paper in new drawingUnconfirmed
0%
Task Description

Yesterday I set up a Windows 64 bit install of QCAD Pro which shows the same bug I have been seeing for a while in the Community linux git repo.

Create a new drawing and then go to “Print preview”. Enable “Move paper postion”, the cursor changes to the hand icon, but the paper position is unable to be moved. Only by saving the drawing, exiting the program, restarting and reopening the drawing, will the “Move paper postion” function correctly.

Affected versions tested:

Windows 64bit installer download, as of yesterday.
Linux 64bit build from git, about 20minutes ago.

For what it’s worth, this bug is not present in this previous git checkout:

Version:
3.21.1.0 (3.21.1)
Internet:
QCAD.org
Build Date:
Jul 2 2018
Revision:

Qt Version:
5.7.0
Architecture:
x86_64
Compiler:
gcc 6.3.1

Thanks for a great product.

 2029 QCAD (main)Bug ReportVery Low Block order issue within drawing exchange between CE an ...Closed
100%
Task Description

If I create a dxf in Pro and open it in CE (or vice versa) the block order can change strange and a new Layout Block is occasionally added. Looks like dxf version (R15 etc.) doesn’t matters.

Versions:
QCAD Pro 3.24.2.0
QCAD CE 3.24.0.0

2048QCAD (main)Bug ReportVery LowMove / Copy to current layer fails when reference point...Assigned
0%
Task Description

QCAD 3.24.2 / macOS x86_64 10.14.6

Starting with empty doc:
1. Draw any object (e.g. a rectangle) on layer 0.
2. Create new layer (”1”) with color, say yellow.
3. Select new layer
4. Select new object
5. Modify → Move / Copy
6. Click reference point
7. Click target point same as reference point
8. In “Move / Copy Options” dialog, select “Delete Original” and check “Use current layer and attributes.” Click OK.

The moved object stays on the layer it was previously on. Using “Move / Copy” as a quick way to move a selection between layers is not useful even though it appears to be the recommended way in a Google search.

Note: if “Keep Original” is selected instead, the copied object is placed on the current layer and the original object remains on its layer, as expected.

Note: if the target point is different from the reference point, the moved object is placed on the current layer as expected.

There are other workarounds too, cut / paste with “To current layer” checked seems to work, as does chaging the layer in the Properties Editor.

 2050 QCAD Community EditionBug ReportVery Low FlexPainter dosen't work Closed
100%
Task Description

FlexPainter works in the Pro version of QCad but not in the Comunity one.
If it’s not supposed to works in the latter, maybe, it would be better to remove it from the menu (Misc > Script Examples > Mathematics).

2068QCAD Community EditionBug ReportVery LowNon-english text in upper/lower index becomes UTF codeAssigned
0%
Task Description

How to reproduce.

1. Create a text field with some non-english words in the upper index. (see attached pic1.png)
2. Save the project and close QCAD.
3. Run QCAD and open same project.
4. Now upper/lower indexed text becomes not human readable UTF codes. (see attached pic2.png)

Tried different fonts - doesn’t help.

Linux ntb-kirill 3.10.0-1062.12.1.el7.x86_64 #1 SMP Tue Feb 4 23:02:59 UTC 2020 x86_64 x86_64 x86_64 GNU/Linux
CentOS Linux release 7.7.1908 (Core)

 2085 QCAD (main)Bug ReportVery Low Drag and drop: moving single polyline vertex moves also ...Closed
100%
Task Description

See the steps to reproduce in the attached drawing.

2088QCAD (main)Bug ReportVery Low column headers of the "General: tool settings " resize...Assigned
0%
Task Description

Open QCAD and the application preferences. In the section “General: tool settings " you can resize the columns: Menu, Shortcuts etc.
The problem is that it is not intuitive. The first divider is not selectable and the second moves the first, only backwards.

2097QCAD (main)Bug ReportVery LowVery hard to snap to baseline reference point of dimens...Assigned
0%
Task Description

With default autosnap settings reference points included I find it very hard to snap to the baseline reference points of a dimension.
I manage to do it by setting snap to reference point only and zoom out till I see the entire dimension element.

2098QCAD (main)Bug ReportVery LowOffset will pick up hidden blocks while using it in a l...Assigned
0%
1 Task Description

When I’m drawing inside a layout block the offset tool picks up lines from blocks that are hidden.
It is not happening with all the block.

 2144 QCAD (main)Bug ReportVery Low Draw > Viewport > Add Viewport: Custom hatch pattern no ...Closed
100%
Task Description

QCAD Professional

Version: 3.25.2.4 (3.25.2.4)
Internet: QCAD.org
Build Date: Nov 18 2020
Revision: 40f4475
Qt Version: 5.13.2
Architecture: i386
Compiler: Unknown

Orphan Hatches (without a *.pat file installed) are no longer visible in a viewport

Topic: https://qcad.org/rsforum/viewtopic.php?f=33&t=7830
Original topic: https://qcad.org/rsforum/viewtopic.php?f=33&t=7340
File: #2 https://qcad.org/bugtracker/index.php?do=details&task_id=2063

Regards,
CVH

 2151 QCAD (main)Bug ReportVery Low Update viewport on Layout after Layer property change Closed
100%
1 Task Description

QCAD Professional
Win installer 32bit
Version: 3.25.2.4 (3.25.2.4)
Internet: QCAD.org
Build Date: Nov 18 2020
Revision: 40f4475
Qt Version: 5.13.2
Architecture: i386
Compiler: Unknown

With the attached file:
Viewing Layout1
Changing ON/OFF or Frozen state of layers in the Layer List

The view doesn’t update immediate.
Selecting an entity: Yes
After QQ Yes
Switching to another Application and reverting the focus back to QCAD: Yes
Using zoom / pan or the Zoom functions: No
Changing the display modes: Yes
Starting an action: No

2155QCAD (main)Bug ReportVery LowFaulty rendering Polyline Arcs with Width = 2RAssigned
0%
1 Task Description

QCAD Professional
Win installer 32bit
Version: 3.25.2.4 (3.25.2.4)
Internet: QCAD.org
Build Date: Nov 18 2020
Revision: 40f4475
Qt Version: 5.13.2
Architecture: i386
Compiler: Unknown

Most likely not related to the QCAD version, rather an old sore.

File included
Topic: https://qcad.org/rsforum/viewtopic.php?f=33&t=7889#p30803
Confirmed by ‘cccplex’ Linux ‘Latest Ubuntu’

Polyline arcs with Width = 2R render as circle segments rather than circle sectors.
As Non-reversed arcs these don’t explode.
As reversed arc these explode to a single arc rather than a circle sector contour.

There is also still the faulty rendering with Z not zero
https://qcad.org/bugtracker/index.php?do=details&task_id=1923

Regards,
CVH

 2175 QCAD (main)Bug ReportVery Low Edit > Application Preferences > Draw > Text: Uncheck a ...Closed
100%
Task Description

In the Application Preferences>Draw>Text dialog, when first opened, the Uncheck all and Check all buttons are not disabled if the Show font preview in font controls check box is checked. If you click on the Use reduced selection of fonts check box twice the buttons become disabled.

2176QCAD (main)Bug ReportVery LowModify > Break out Manual: relevance of order of click ...Assigned
0%
1 Task Description

QCAD Professional
Windows 7; Win installer 32 bit
Version: 3.25.2.7 (3.25.2.7)
Internet: QCAD.org
Build Date: Dec 16 2020
Revision: e06f230
Qt Version: 5.13.2
Architecture: i386
Compiler: Unknown

Forum Topic: https://qcad.org/rsforum/viewtopic.php?t=7988
File included.
I have no intention to make 48 separate reports.

CVH

 2193 Command line toolsBug ReportVery Low dwg2csv retains the last encountered custom properties Closed
100%
Task Description

QCAD Professional
Win installer 32 bit
Version: 3.25.2.13 (3.25.2.13)
Internet: QCAD.org
Build Date: Feb 12 2021
Revision: cad2d36
Qt Version: 5.13.2
Architecture: i386
Compiler: Unknown

Andrew,
While enhancing DrawFromCSV: Forum Link.
I had a peek at the new command line tool: dwg2csv

I would never come up with 115 columns.
That wouldn’t be efficient to generate entities from.
Although this way it is very complete and one could use specific lists to filter.
One downside is that the ‘-list’ switch return is far too vast for the windows command line.



Remarked that:
Only the first alphabetically custom property is listed under:
QCAD:Line & QCAD:Reference (columns 114-115).
And that the last encountered is persistent for all entities that follows.

Maybe this originates from a multiple entity selection ...
... what also retains the last encountered custom properties in the property editor.
Should I add a seperate task for that?



Also had an exception thrown:
Debug: dropped global XDATA (no res buf): “ViewportCenter”.
Discarted that as this very basic test drawing hasn’t even a Viewport.

Regards,
CVH

Added: Snippet from DrawFromCSV code (merely a test case)

CSVcomma/semicolon
Offset;50;50
Point;39,789355;-0,815325;+[Custom;Reference:101];
Point;38,49526;4,014304;+[Custom;Reference:102;Line:56]

The two points, and only those two points, are casted with custom properties
QCAD|Reference|101
QCAD|Reference|102 & QCAD|Line|56

Added: The dxf file
Added: The csv file (change to the comma/semicolon style)

2194QCAD (main)Bug ReportVery LowMultiple selection of entities with custom properties d...Assigned
0%
1 Task Description

QCAD Professional
Win7 installer 32 bit
Version: 3.25.2.13 (3.25.2.13)
Internet: QCAD.org
Build Date: Feb 12 2021
Revision: cad2d36
Qt Version: 5.13.2
Architecture: i386
Compiler: Unknown

In the file provided one would expect *VARIES* in the property editor under custom properties when selecting 2 or more entities.
The key list is reduced to what keys are common to the multiple selection. (Here 3)
The values displayed are inconsistent depending the selection.

Select All » 3 custom properties of line 3
Select the 3 vertical » 3 custom properties of line 2
Select the first vertical and the diagonal » 3 custom properties of line 1
Select all but the first vertical » 3 custom properties of line 3
And so on ...

Regards,
CVH

 2212 QCAD (main)Bug ReportVery Low Cannot change f5 shortcut in preferences. Closed
100%
Task Description

I’d like to change the f5 shortcut from rotate counter-clockwise to move/copy.

I started with a fresh QCAD3.conf

In the preferences window: general: tool settings

First time I remove f5 from rotate counter-clockwise qcad crashes.
Second run it seems to work.
I add the shortcut f5 to move/copy and restart.
The shortcut doesn’t work. And tool settings has a notice that there are conflicts.
When I change it to f3 it works.

btw the shortcut column don’t show any shortcuts. See screenshot.

2218ECMAScriptBug ReportVery LowRPolyline.appendVertex() doesn't default to width = zer...Assigned
0%
1 Task Description

When I use poly.appendVertex(vector, bulge) the polyline is finally created with NAN widths

This, while the signature explains that bulge, width1 and width2 default to zero.
https://www.qcad.org/doc/qcad/latest/developer/class_r_polyline_entity.html#a9ee706e50d6cc267fc84a85b7c81d5e6

Regards,
CVH

 2223 QCAD (main)Bug ReportVery Low Block > Insert Block: duplicate entries in attributes c ...Closed
100%
Task Description

Insert block with multiple instances of the same attribute definition (same tag).
Attributes combo box shows multiple entries for the same attribute.

 2225 QCAD (main)Bug ReportVery Low Filenames containing an ampersand do not render correct ...Closed
100%
Task Description

If a file is opened whose filename contains an ampersand, the filename will be rendered correctly in the application titlebar, but the tab bar and the Window menu will not display the ampersand.

If, however, the ‘alt’ key is pressed, the ampersand will result in an underscore appearing beneath the character immediately following it in the filename string. This applies both to the titlebar and the Window menu.

Interestingly, this can be “exploited” by a user to quickly switch between tabs by pressing ‘alt’ and the character which follows the ampersand simultaneously. Likewise, a user can swap between windows using the Window menu in a similar fashion, by first pressing Alt+W, then Alt and the same key as before.

The expected result is that the ampersand is rendered, the underscore is not rendered, and the ‘alt’ key shortcuts don’t work.

It would appear that this is a simple case of failing to properly escape the ampersand in filenames before passing the filename string to various Qt methods.

 9 QCAD (main)Bug ReportLow RSettings.setValue() doesn't work for "GraphicsViewColo ...Closed
100%
Task Description

Context: Needed to set color settings for book images.

"GraphicsViewColors/BackgroundColor""GraphicsViewColors/MetaGridColor"

QCAD3.conf:

[email protected](\0\0\0\x7f\0\0\0\aRColor\0\x1\xff\xff\0\0\0\0\0\0\0\0\0\x2)
MetaGridColor  [email protected](\0\0\0\x7f\0\0\0\aRColor\0\x1\xff\xff\xff\xff\xfe\xfe\xfd\xfd\0\0\0\x2)

Setting the alpha channel value and the color mode for RColor doesn’t change anything.
Using view.setBackgroundColor() instead works for the background color, but not for other colors such as the meta grid color.

 10 BookBug ReportLow Book numbering in PDF is incorrect Closed
100%
Task Description

The numbers in the book don’t match with the bookmarks numbers in the PDF as shown in Acrobat Reader.

 17 ECMAScriptBug ReportLow RLineEntityPointer doesn't work as function argument of ...Closed
100%
Task Description

Script code (SvgExporter.js):

245 // only export entities on main block "*Model_Space":
246 if (realEntity.getBlockId() == this.doc.getBlockId("*Model_Space")) {
247   RFileExporterAdapter.prototype.exportEntity.call(this, entity, false);
248 }

Script debugger exception:

Uncaught exception at /home/martin/workspace/rsframework/scripts/File/SvgExport/SvgExporter.js:246:
Error: :-1:-1: RExporter: Argument 0 is not of type REntity*.
<native>(RLineEntityPointer(0xb6fb158), false) at -1
<anonymous>(entity = RLineEntityPointer(0xb6fb158), preview = false) at
/home/martin/workspace/rsframework/scripts/File/SvgExport/SvgExporter.js:246
<anonymous>() at /home/martin/workspace/rsframework/scripts/File/SvgExport/SvgExporter.js:211

Workaround: Used exportEntity() with ID as argument instead. However there may be other cases where no alternative method is available.

RFileExporterAdapter.prototype.exportEntity.call(this, realEntity.getId());
 18 QCAD (main)Bug ReportLow LineRectangleSize.js: options tool bar: alignment point ...Closed
100%
Task Description

Sometimes the popup widget that lets the user choose the alignment point for positioning the rectangle does not close when the user clicks the desired point.

 22 QCAD (main)Bug ReportLow Improve grid info display for imperial units Closed
100%
Task Description

For inch, foot, .. the grid info display should for example display “1/128” instead of 0.0078125

 28 QCAD (main)Bug ReportLow Test Recorder Closed
100%
Task Description
  • copy actual drawing to required (Tab “Results” context menu)
 33 QCAD (main)Bug ReportLow Prints always to A4 Closed
100%
Task Description

Print prints always to A4, regardless of paper size chosen.

 34 QCAD (main)Bug ReportLow Printing tests Closed
100%
Task Description

Iterate through all drawings in a directory and create PDFs from them using the same mechanism as for printing.

 39 QCAD (main)Bug ReportLow print of not found (invalid) layer crashes Closed
100%
Task Description
"dummy"
Thread [1] 23305 (Suspended : Signal : SIGSEGV:Segmentation fault)	
	RLayer::getLinetypeId() at 0x898faae	
	operator<<() at RLayer.cpp:141 0x8df7ce4	
	REcmaSharedPointerLayer::toString() at REcmaSharedPointerLayer.cpp:1,885 0x8b1ab59	
	0xb6bd913c	
	0xb6ac2f68	
	0xb6ac3058	
	0xb6b09fb5	
	0xb69ed8e7	
	0xb6b083d5	
	0xb6a5a992	
	<...more frames...>	
 42 QCAD (main)Bug ReportLow Text Dialog: bold / italic main font Closed
100%
Task Description

bold / italic check box for main font has no effect

 47 QCAD (main)Bug ReportLow Print preview marks drawing as modified Closed
100%
Task Description

Print preview marks drawing as modified

 48 QCAD (main)Bug ReportLow Close drawing from print preview Closed
100%
Task Description

Fails if drawing was modified and user wishes to save drawing.

 50 QCAD (main)Bug ReportLow Text dialog: Uncaught exception Closed
100%
Task Description
  1. open text dialog
  2. select some characters (for coloring)
  3. click on the “color” button → a pop up windows appears showing all colors
  4. don’t choose a color, but click somewhere outside the pop up window
'chosenAction'"color"
 51 QCAD (main)Bug ReportLow Text Dialog: remember last used settings Closed
100%
Task Description

Remember last used settings (text size, font, ...)

Showing tasks 51 - 100 of 2225 Page 2 of 45 - 1 - 2 - 3 - 4 - 5 - Last >>

Available keyboard shortcuts

Tasklist

Task Details

Task Editing